Kärcher MT HT 550/36 Mode D'emploi page 15

Sharpening the blade sections
Note
Remove as little material as possible during sharpening
and maintain the original angle of the blade tooth in the
process.
CAUTION
Sharp blade
Incision injuries
Malfunctions often have simple causes that you can
remedy yourself using the following overview. When in
doubt, or in the case of malfunctions not mentioned
here, please contact your authorised Customer Service.
Fault
The device stops during
operation
Problems when mount-
ing the shaft compo-
nents
Warranty
The warranty conditions issued by our relevant sales
company apply in all countries. We shall remedy possi-
ble malfunctions on your appliance within the warranty
period free of cost, provided that a material or manufac-
turing defect is the cause. In a warranty case, please
contact your dealer (with the purchase receipt) or the
next authorised customer service site.
(See overleaf for the address)
Technical data
Device performance data
Working voltage of the bat-
tery
Maximum speed
Cutting blade length
Tooth pitch
Working range (max.)
Dimensions and weights
Length x width x height
Weight (with battery pack) kg
Device performance data (measured with MT 36 Bp
Multi-Tool)
Max. speed
Sound power level as per EN 62841-1 and
EN 62841-4-2 (measured with MT 36 Bp Multi-Tool)
Sound pressure level L
pA
Uncertainty K
pA
Sound power level L
wA
Uncertainty K
WA
Troubleshooting guide
Cause
Blade blocked with cutting material.
Motor has overheated
The connection points are dirty.
MT 36 MT HT
Bp 550/36
V 36
/min 10000 ±
10%
cm 55
mm 28
m 3,1
mm 951 x 1305 x
197 x 125 x 87
188
2,6 2,3
/min 1820 ±
10%
dB(A) 85,9
dB(A) 3,0
dB(A) 93,9
dB(A) 0,5
Wear suitable protective gloves when sharpening the
blade sections.
1. Clamp the blade in a vice.
2. Sharpen the exposed side of the blade teeth with a
file.
3. Carefully push the blade further by hand so that the
unsharpened blade teeth are accessible.
4. Sharpen the exposed side of all blade teeth with a
file.
As the battery pack ages, even if it is looked after, its ca-
pacity reduces such that the full run time will no longer
be reached when fully charged. This does not indicate a
defect.
Rectification
 Remove cutting material from the blade.
 Stop working and allow the motor to cool
down.
 Clean the shaft ends of adhering dirt.
 Only place the accessories on clean sur-
faces.
Vibration value according to EN 62841-1 and
EN 62841-4-2 (measured with MT 36 Bp Multi-Tool)
Front handle hand-arm vi-
bration value
Rear handle hand-arm vi-
bration value
Uncertainty K
Subject to technical modifications.
Vibration and noise value
The total vibration values given and the noise emission
values given were measured according to a standard
test procedure and can be used to compare one tool
with another. The declared total vibration values and the
declared noise emission values can also be used for a
preliminary exposure assessment.
WARNING
Vibration and noise emissions during actual use of the
power tool may differ from the values given, depending
on the tool and in particular the type of workpiece used.
Identify the safety measures to protect the operator on
the basis of an exposure estimate under actual use con-
ditions (taking into account all parts of the operating cy-
cle, such as the release time).
Device with a hand-arm vibration value
> 2.5 m/s² (see chapter Technical Data in the
operating instructions)
CAUTION
for several hours can lead to numbness. ● Wear warm
gloves to protect your hands. ● Take regular breaks
from work.
English
MT 36
Bp
2
m/s
2
m/s
2
m/s
● Uninterrupted use of the device
MT HT
550/36
3,8
3,0
1,5
15