Installing And Removing The Battery Pack - DeWalt Max DCE300 Guide D'utilisation

D WALT CRIMP CONNECT™ System
e
This crimping tool is capable of connecting with a computer
via the micro USB port on the back of the tool using the
12
micro USB cable included with your tool. This allows the
user to connect the D WALT crimping tool to a computer
e
which utilizes D WALT's CRIMP CONNECT
e
nOTE: The CRIMP CONNECT™ System software is governed
by separate terms and conditions available for viewing
through the software download.
step 1: Download the CRIMP CONNECT™ System software
to your computer at www.dewalt.com/crimpconnect.
step 2: Follow the instructions in the software to create
your CRIMP CONNECT™ System account.
step 3: Connect your crimping tool with the D
CRIMP CONNECT™ System software by first connecting the
provided micro USB cable to the micro USB port
back of the tool to a USB port on a computer. Then go to
the Home screen of the program to access tool tracking and
usage reports stored on the crimping tool.
nOTE: The USB connection will not charge the tool's
battery pack.
For more information on D WALT CRIMP CONNECT™ System
e
functionality and features, please call 1–800–4-D
(1–800–433–9258), visit www.D
page and help screens located inside the software.
ASSEMBLY AND ADJUSTMENTS

WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start-up can cause injury.

WARNING: To reduce the risk of serious personal
injury, do not use the crimping tool with any kind of
die other than those recommended by D
Changing the Dies (Fig. A)

WARNING: Inspect dies and connectors
before use. Only use properly matched dies
and connectors for the crimping head. Refer
to Die Compatibility Chart for die/connector
compatibility.
1. Remove the battery pack.
2. Clean the die holder with a dry clean cloth or
1
forced air.
3. Select the appropriate size and type of crimping die for
the connector and cable specified. Refer to engineering
specifications and the Die Compatibility Chart.
4. Slide the dies into each die holder
detent snaps into the die groove. This locks the die
into place.
5. To remove the dies, first remove the battery pack, then
completely open the hydraulic ram by pressing and
holding the reverse trigger switch. Apply force to left or
right side of the die until die slides out of die holder.
TM System software.
WALT
e
on the
12
WALT
e
WALT.com or view the FAQ
e
WALT.
e
1 until the ball
OPERATION

WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start-up can cause injury.

Installing and Removing the Battery Pack

(Fig. E)
nOTE: For best results, make sure your battery pack is
fully charged.
To install the battery pack into the tool handle, align the
battery pack with the rails inside the tool's handle and slide
it into the handle until the battery pack is firmly seated in
the tool and ensure that it does not disengage.
To remove the battery pack from the tool, press the release
button and firmly pull the battery pack out of the tool
handle. Insert it into the charger as described in the charger
section of this manual.
FIG. E
Proper Hand Position (Fig. F)

WARNING: To reduce the risk of serious personal injury,
ALWAYS use proper hand position as shown.

WARNING: To reduce the risk of serious personal injury,
ALWAYS hold securely in anticipation of a sudden
reaction.
Proper hand position requires one hand on the main handle
as shown.
6
FIG. F

WARNING: CUT OR AMPUTATION HAZARD. Never
have any part of your body near the crimping head or
moving parts during the crimp cycle, or whenever the
main power is ON. Serious personal injury may occur.

WARNING: Proper material preparation and
installation is the responsibility of the installing
contractor.

WARNING: The crimp connectors must be used
in compliance with applicable building codes
English
6
9