Westin Automotive Products 32-1600 Consignes

AUTOMOTIVE PRODUCTS, INC.
BULL BAR ASSEMBLY
ENSAMBLE DE PARRILLA
DELANTERA CON TIRÓN
LA BULL BAR
32-1600
32-1605
ITEM QTY
1 1 BULL BAR ASSEMBLY
2,3 2 BRACKET, PASSENGER (2) AND DRIVER (3)
4 2 PLASTIC PLUG
5 4 RUBBER BUMPER
6 4 3/8-16 X 1.25" HEX HEAD BOLT,
7 8 3/8" SAE FLAT WASHER
8 4 3/8" LOCK WASHER
9 4 3/8-16 HEX NUT
10 2 3/8-16 X 4.50" HEX HEAD BOLT
11 2 3/8" SAE FLAT WASHER
12 2 3/8" USS FLAT WASHER
13 2 3/8" LOCK WASHER
14 2 3/8-16 HEX NUT
15 4 SPACER WASHER
1 1 ENSAMBLE DE PARRILLA DELANTERA CON TIRÓN
2,3 2 SOPORTE, ACOMPAÑANTE
4 2 PLACAS DE PERNOS
5 4 TAPONES DE PLÁSTICO
6 4 PERNOS CON CABEZA HEXAGONAL DE 3/8-16 X 1,25"
7 8 ARANDELA PLANA SAE DE 3/8"
8 4 ARANDELAS DE PRESIÓN DE 3/8"
9 4 TUERCAS HEXAGONALES DE 3/8-16
10 2 PERNOS CON CABEZA HEXAGONAL DE 3/8-16 X 4,50"
11 2 ARANDELAS PLANAS SAE DE 3/8"
12 2 ARANDELAS PLANAS USS DE 3/8"
13 2 ARANDELAS DE PRESIÓN DE 3/8"
14 2 TUERCAS HEXAGONALES DE 3/8-16
15 4 ARANDELAS SEPARADORAS
1 1 LA BULL BAR
2,3 2 SUPPORT, PASSAGER (2) ET CONDUCTEUR (3)
4 2 BOUCHONS DE PLASTIQUE
5 4 PARE-CHOCS CAOUTCHOUC
6 4 BOULONS A TETE HEXAGONALE 3/8-16 X 1,25 PO
7 8 RONDELLES PLATES SAE 3/8 PO
8 4 RONDELLES A FREIM 3/8 PO
9 4 ÉCROUS HEXAGONAUX 3/8 PO
10 2 BOULONS A TETE HEXAGONALE 3/8-16 X 4,50 PO
11 2 RONDELLES PLATES SAE 3/8 PO
12 2 RONDELLES PLATES USS 3/8 PO
13 2 RONDELLES A FREIN 3/8 PO
14 2 ÉCROUS HEXAGONAUX 3/8-16
15 4 RONDELLES D'ESPACEMENT
Remove the contents from box and check for damage. Verify all parts are present. Read instructions completely before
STEP 1.
beginning. NOTE: Westin advises the installer to use a thread lubricant on all of the stainless steel fasteners.
NOTE: It may be necessary to remove/relocate front license plate and license plate bracket. It is not required, but strongly
STEP 2.
recommended. If local/state laws requires a license plate, license plate relocation kit 32-0055 is available.
Determine passenger and driver brackets. From underneath vehicle, remove tow hooks. Tow hooks will not be reinstalled.
STEP 3.
Locate the two studs that hold the bumper support to the frame. Remove the nuts and install mount bracket onto the
studs and replace factory nuts. Insert the 3/8-16 x 4.50" bolt through the frame and into the mount bracket. Secure with
3/8" yellow zinc fasteners as shown. SEE FIGURE 2.
INSTRUCTIONS-INSTRUCCIONES-CONSIGNES
APPLICATION: 2005-07 TOYOTA TACOMA
APPLICATION: TOYOTA TACOMA, MOD. 2005-07
APPLICATION:
1
CONTENTS - CONTENIDO - CONTENU
(2) Y EL CONDUCTOR
TOYOTA TACOMA 2005-07
(3)
2
TOOLS - HERRAMIENTA - OUTILS
9/16" SOCKET
9/16" WRENCH
17MM SOCKET
14MM DEEP SOCKET
RATCHET
TORQUE WRENCH
DADO DE 9/16"
LLAVE DE TUERCAS DE 9/16"
DADO DE 17 MM
DADO DE ALCANCE PROFUNDO DE 14
MM
MANERAL
LLAVE DE TORQUE
DOUILLE 9/16 PO
CLE 9/16 PO
DOUILLE 17MM
DOUILLE PROFONDE 14MM
CLIQUET
CLE DE COUPLE
WO: 75-0444 REVISION A 3/20/08
3