Power Supply - Monacor SAM-2 Mode D'emploi

Masquer les pouces Voir aussi pour SAM-2:
Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 12
5.2 Outputs
Connect the RCA jacks SAT OUT (15) to the inputs
of a stereo power amplifier operating the satellite
speakers .
In case of separable full amplifiers of high qual-
ity provided with a controlled preamplifier output
(possibly marked "Pre Out") and a power amplifier
input (possibly marked "Amp In"), it is also possible
to insert the module SAM-2 into the full amplifier:
Connect the jacks LINE IN (14) to the preamplifier
output and the jacks SAT OUT (15) to the power
amplifier input .

5.3 Power supply

Finally connect the supplied mains cable first to
the mains jack (11) and then to a mains socket
(230 V/ 50 Hz) .
6 Operation
Any adjustments and sound evaluations must only
be made in connection with the satellite speakers .
The sound should be evaluated at the final place
of hearing where a second person at the active
subwoofer should be instructed to find the best
adjustment .
1) Switch on the active speaker system with the
switch POWER (10) . As long as no input signal
is available, the system is in the power-saving
stand-by mode and the LED indicator (2) shows
red . As soon as an input signal is available, the
power amplifier is switched on and the LED
shows green .
10
1
GREEN – ON
RED
– STAND-BY
2
SUB
SUB
LEVEL
CROSSOVER
100 Hz
MIN
MAX
50 Hz
150 Hz
3
4
SAM-2 ACTIVE SUBWOOFER MODULE
POWER
250
10
230 V ~ / 50 Hz / 300 VA
11
12
T3.15AL
SUB-BOOST
FREQUENCY
LEVEL
PHASE
40 Hz
°
30 Hz
50 Hz
0
+ 6 dB
0
5
6
• 200
/ 4
• 125
/ 8
W MAX
W RMS
W RMS
LEFT
RIGHT
13
HIGH LEVEL INPUT
If no signal is available, the active speaker
system will return to stand-by (LED = red) after
approx . 7 minutes . If the active speaker system
is not used for a longer period, it should be
switched off with the switch POWER, otherwise
the stand-by mode will always have a low cur-
rent consumption .
If the automatic switchover between stand-
by and operation does not function optimally,
the switch-on threshold can be modified in the
range of 1 – 10 mV . The control for the switch-on
threshold is in the position RVa on the PCB of
the preamplifier (see page 35) . The further the
control is turned clockwise, the higher the input
level at which the module will be switched on .
2) If a ground loop has been created by the con-
nection, humming will occur (e . g . with music
passages of low volume) . This ground loop can
be interrupted with the groundlift switch (9) .
On the other hand, the amplifier is not shielded
from electric noise fields if the front plate is not
grounded . In case of doubt, set the switch
alternately to find the best adjustment .
3) Use the control SUB CROSSOVER (4) to adjust
the upper crossover frequency, i . e . the fre-
quency which is not to be reproduced any more
by the subwoofer (the lower the upper cross-
over frequency, the more difficult the acoustic
localization of the subwoofer; the higher the
crossover frequency, the more powerful the bass
support) . In most cases, shelf speakers and small
SUB
SAT
CROSSOVER
100 Hz
°
180
50 Hz
150 Hz
7
8
GND
LIFT
9
GROUND
LIFT
14
15
LINE IN
SAT OUT
RIGHT
LEFT

Publicité

Table des Matières
loading

Table des Matières