Professional Mode - Laserworld ShowNET Mode D'emploi

Manual: Laserworld ShowNET - Network Interface

(2) Professional Mode

Channel Mode Value
1 Intensity Prof. 0
1 - 255
2 Pattern selection Prof. 0
1 - 255
3 Pattern speed Prof. 128
(Framerate)
0 - 127
129 - 255
4 Position X-axis coarse Prof. 0 - 255
5 Position X-axis fine Prof. 0 - 255
6 Position Y-axis coarse Prof. 0 - 255
7 Position Y-axis fine Prof. 0 - 255
8 Rotation coarse Prof. 0 - 255
9 Rotation fine Prof. 0 - 255
10 Size X-axis Prof. 0 - 255
11 Size Y-axis Prof. 0 - 255
12 Inversion Prof. 0 - 63
64 - 127
128 - 191
192 - 255
13 Color Selection Prof. 0 - 15
16 - 207
208 - 223
224 - 239
240 - 255
14 Red Prof. 0 - 255
15 Green Prof. 0 - 255
16 Blue Prof. 0 - 255
page 14 / 54
Function
Laser off
Increase intensity (full intensity = 255)
Blackout (000.ild must not exist)
Display patterns from SD card:
1 = 001.ild
2 = 002.ild
... and so on
If no pattern is assigned to a number = blackout
Standard speed 50 fps
Increasing speed from 0 fps tp 50 fps
Increasing speed from 50 fps to 100 fps
From left (0) to right (255); center = 128
From bottom (0) to top (255); center = 128
Rotate; 0° = 128
From maximum (0) to minimum (255)
From maximum (0) to minimum (255)
None
Invert X-axis
Invert Y-axis
Invert X + Y-axis
Original pattern colors
Color selection from red (16) through yellow
(48), green (80), cyan (112) and blue (144) up to
purple (176) with color mixtures in between.
White with half intensity for each color channel
White with full intensity for each color channel
Enables channels 14 -16 to select a specific hue
Increase intensity red
Only active if the value of channel 13 is 240 - 255
Increase intensity green
Only active if the value of channel 13 is 240 - 255
Increase intensity blue
Only active if the value of channel 13 is 240 - 255
Channel Mode Value
17 Strobe Prof. 0 - 15
16 - 255
18 Scan speed Prof. 0 - 15
16 - 255
19 Safety zone size Prof. 0 - 63
64 - 127
128 - 191
192 - 255
20 Safety zone intensity Prof. 0 - 255
21 Color balancing red Prof. 0 - 255
(for white balance)
22 Color balancing Prof. 0 - 255
green
(for white balance)
23 Color balancing blue Prof. 0 - 255
(for white balance)
IMPORTANT: Channels 24 - 34 are reserved for future features and must not be assigned
Important Note:
Operate scanners/galvos only at appropriate speed according to the res-
pective scan angle. Too high scan speed will damage the scanning system.
Manual: Laserworld ShowNET - Network Interface
Function
None
Increasing strobe effect
Default
Increasing scan speed (from 5 kpps to 40 kpps)
Size of horizontal safety zone
Safety zone is the bottom side
Size of horizontal safety zone
Safety zone is the upper side
Size of vertical safety zone
Safety zone is the left side
Size of vertical safety zone
Safety zone is the right side
From max intensity (0) to no intensity (255)
From max intensity (0) to no intensity (255)
Master to channel 14!
From max intensity (0) to no intensity (255)
Master to channel 15!
From max intensity (0) to no intensity (255)
Master to channel 16!
page 15 / 54