Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
Manual: Laserworld ShowNET - Network Interface
This setting is especially suitable for demo purposes or for fixed laser installations.
The stand-alone mode allows for additional advanced features: As standard, the stand-
alone mode cycles through the ILDA files on the SD cards and plays them consecutively
and in a general loop.
If DIP switch 4 is activated too, the stand alone mode only plays one specific ILDA file and
just loops this file.
switch
1
2
3
4
On (1) / Off (0)
0
0
0
1
Dip switch 1 can be used to step to the next file (just switch DIP switch 1 to on, then to
off again)
Dip switch 2 can be used to step to the previous file (just switch DIP switch 2 to on, then
to off again)
c)
Demo Mode / Automatic Animation
switch
1
2
3
4
On (1) / Off (0)
0
0
0
0
In demo mode the ILDA files on the plugged in SD card are triggered automatically. The
ILDA files are not only played back like in the stand alone mode, but they are also auto-
matically animated by ShowNET's internal intelligence. This creates dynamic animations,
even if only static frames are on the SD card.
This setting is especially suitable for demo purposes.
d)
Master-Slave-Mode: Demo Mode
MASTER Unit:
switch
1
2
3
4
On (1) / Off (0)
0
0
0
0
SLAVE units:
switch
1
2
3
4
On (1) / Off (0)
0
0
0
0
To have the same effects show on all connected units, it is required to have the same
pattern sets on all SD cards inside the units.
e)
ArtNet Operation
IMPORTANT: ArtNet operation requires the ShowNET interface to be connected in a
DHCP environment (router with integrated switch is recommended). The address hand-
ling must be managed through DHCP. For questions on DHCP, please refer to 4.1. DHCP
Mode.
Only ShowNET interfaces and the ArtNet controller must be used in the same network.
Avoid using other network devices in the same network.
page 10 / 54
5
6
7
8
9
10
0
1
0
1
0
0
5
6
7
8
9
10
1
0
0
0
1
0
5
6
7
8
9
10
0
1
0
0
1
0
5
6
7
8
9
10
0
1
1
1
0
0
Use the dip switches to assign a certain address like in DMX mode:
switch
1
2
3
4
5
Binary DMX
1
2
4
8
16
channel offset
To activate ArtNet trigger, open the admin tool and navigate to the tab ‚Settings' . Then
change the ‚Data source for internal DMX effects' to ‚ArtNet input' as seen in the picture
below:
Click on ‚Store Data' to save the changes. Click on ‚OK' twice and wait until another win-
dow opens that asks to restart the ILDA interface. To do so, switch the laser system off
and on again.
See the details on DMX Mode below for more information:
f)
DMX Modes
switch
1
2
3
4
5
Binary DMX
1
2
4
8
16
channel offset
There are two DMX / ArtNet configuration modes:
(1) DJ Mode & (2) Professional Mode.
The DJ mode is more basic and comes with some pre-configured automations. It is sui-
table for most users.
The Professional mode comes with some advanced features and requires deper know-
ledge of DMX / ArtNet to be handled properly.
DJ mode is the standard option. To use the Professional mode, open the admin tool and
navigate to the tab ‚Settings' .
Manual: Laserworld ShowNET - Network Interface
6
7
8
9
10
32
64
128
256
Switch 10 has to be ON (up)
for ArtNet operation
6
7
8
9
10
32
64
128
256
Switch 10 has to be ON (up)
for DMX mode
page 11 / 54
Publicité
Table des Matières
