Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
Manual: Laserworld ShowNET - Network Interface
d)
ILDA Streaming
The Laserworld ShowNET interface is capable to act as range extender for ILDA signals by
tranforming an incoming ILDA signal on the ILDA IN interface to a standard UDP network
signal and transferring this signal back to standard ILDA in a receiver unit (obviously an
external ShowNET interface is required as sender for this kind of application!) . Do NOT
send the signal over Wifi, this transmission method is not suitable in a professional envi-
ronment.
Sender-Receiver configuration for ILDA over LAN, range extender use
The sender uses an IP address range between 192.168.2.70 and 192.168.2.85 and trans-
mits the signal to a receiver that has addresses in the range between 192.168.2.50 and
192.168.2.65. The specific IP addresses need to be set with DIP switches. Make sure there
are no other devices in the same network that use the same IP addresses.
Dip switch setting
switch
1
2
3
On (1)
0000 -> IP sender: 192.168.2.70 sends to 192.168.2.50
/ Off
0001 -> IP sender: 192.168.2.71 sends to 192.168.2.51
(0)
0010 -> IP sender: 192.168.2.72 sends to 192.168.2.52
0011 -> IP sender: 192.168.2.73 sends to 192.168.2.53
0100 -> IP sender: 192.168.2.74 sends to 192.168.2.54
0101-> IP sender: 192.168.2.75 sends to 192.168.2.55
0110 -> IP sender: 192.168.2.76 sends to 192.168.2.56
0111 -> IP sender: 192.168.2.77 sends to 192.168.2.57
1000 -> IP sender: 192.168.2.78 sends to 192.168.2.58
1001 -> IP sender: 192.168.2.79 sends to 192.168.2.59
1010 -> IP sender: 192.168.2.80 sends to 192.168.2.60
1011 -> IP sender: 192.168.2.81 sends to 192.168.2.61
1100 -> IP sender: 192.168.2.82 sends to 192.168.2.62
1101 -> IP sender: 192.168.2.83 sends to 192.168.2.63
1110 -> IP sender: 192.168.2.84 sends to 192.168.2.64
1111 -> IP sender: 192.168.2.85 sends to 192.168.2.65
Example:
Sender IP address setting:
switch
1
2
3
4
On (1) / Off (0)
0
0
0
1
This assigns IP address 192.168.2.71 to the Sender.
The corresponding receiver needs this IP address setting:
switch
1
2
3
4
On (1) / Off (0)
0
0
0
1
This assigns IP address 192.168.2.51 to the receiver.
The only difference between sender and receiver configuration is dip switch 5, which is 0 for the
sender and 1 for the receiver.
6. Power Supply
Use the power supply (included in delivery) to connect the ShowNET Interface to mains.
page 18 / 54
4
5
6
7 8
9
sender: 0
0
1 1
0
receiver: 1
5
6
7
8
9
10
0
0
1
1
0
0
5
6
7
8
9
10
1
0
1
1
0
0
Final statement
Product and package leaving warehouse without faults. Users have to follow the local safety
regulations and warnings of this manual. Damages through inappropriate use do not unterlie
the sphere of influence of manufacturer or dealer. Therefore no liability or warranty will be
taken over. We cannot inform you in case of changes of this manual. If you have any questions,
please contact your dealer.
For service please contact your dealer or Laserworld. Please use only spare parts of Laserworld.
Subject to change without notice. Because of the vast amount of data we cannot guarantee
any correctness of given information.
Laserworld (Switzerland) AG
10
0
Kreuzlingerstrasse 5
8574 Lengwil
Switzerland
Registered office:
8574 Lengwil / Switzerland
Company number: CH-440.3.020.548-6
Commercial Registry Kanton Thurgau
CEO: Martin Werner
VAT no. (Switzerland): 683 180
UID (Switzerland): CHE-113.954.889
VAT no. (Germany): DE 258030001
WEEE-Reg.-No. (Germany): DE 90759352
www.laserworld.com
info@laserworld.com
representative according to EMVG:
Ray Technologies GmbH
Managing Director: Martin Werner
Mühlbachweg 2
83626 Valley / Germany
Manual: Laserworld ShowNET - Network Interface
page 19 / 54
Publicité
Table des Matières
