Sauder Barrister Lane 418705 Mode D'emploi
  1. Manuels
  2. Marques
  3. Sauder Manuels
  4. Ameublement d'intérieur
  5. Barrister Lane 418705
  6. Mode d'emploi
Sauder Barrister Lane 418705 Mode D'emploi

Sauder Barrister Lane 418705 Mode D'emploi

Masquer les pouces
Table des Matières

Publicité

Liens rapides

Télécharger ce manuel
sauder.com
Night Stand
Barrister Lane Collection | 418705
Need help? Visit Sauder.com to view video assembly tips or chat with a live rep.
Prefer the phone? Call 1-800-523-3987.
Share your journey!
Sweet stand.
Sweet dreams.
NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
English pg 1-23
Français pg 24-26
Español pg 27-29
Lot # 372269
06/24/15
Purchased: __________________
Be sure to give us a ring before
making any returns. 1-800-523-3987

Publicité

Table des Matières
loading

Manuels Connexes pour Sauder Barrister Lane 418705

Sommaire des Matières pour Sauder Barrister Lane 418705

  • Page 1 Barrister Lane Collection | 418705 NOTE: THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. Need help? Visit Sauder.com to view video assembly tips or chat with a live rep. PLEASE READ AND KEEP FOR FUTURE REFERENCE. Prefer the phone? Call 1-800-523-3987.
  • Page 2 Assembly Tools Required Part Identifi cation No. 2 Phillips Screwdriver Tip Shown Actual Size Hardware Identifi cation Assembly Steps 6-23 Hammer Not actual size Français 24-26 Español 27-29 Skip the power trip. Safety This time. Warranty Page 2 418705 www.sauder.com/services...

  • Page 3: Part Identifi Cation

    DRAWER LEFT SIDE (1) BOTTOM (1) DRAWER FRONT (1) D163 DRAWER BACK (1) SHELF (1) FRONT MOLDING (1) D723 DRAWER BOTTOM (1) BACK (1) RIGHT MOLDING (1) DRAWER BRACE (1) BRACE (1) LEFT MOLDING (1) D163 D723 www.sauder.com/services 418705 Page 3...
  • Page 4 EXTENSION SLIDE - 2 10A SLIDE CAM - 2 HIDDEN CAM - 13 CAM DOWEL - 13 MOLDING METAL BRACKET - 5 PULL - 1 CONNECTOR - 2 KNOB - 1 NAIL - 24 METAL PIN - 2 Page 4 418705 www.sauder.com/services...

  • Page 5: Table Des Matières

    BLACK 1-1/4" FLAT HEAD SCREW - 4 SILVER 1-1/8" FLAT HEAD SCREW - 7 18S BROWN 1" FLAT HEAD SCREW - 4 SILVER 3/4" MACHINE SCREW - 1 30S BLACK 1-9/16" FLAT HEAD SCREW - 5 BLACK 7/8" MACHINE SCREW - 2 www.sauder.com/services 418705 Page 5...
  • Page 6 Look for this icon. It means a Step 1 video assembly tip is available at www.sauder.com/services/tips Assemble your unit on a carpeted fl oor or on the empty å carton to avoid scratching your unit or the fl oor. Push thirteen HIDDEN CAMS (1F) into the ENDS (A å...
  • Page 7 SCREW into this hole. Push the black lever in and pull the SLIDE from the RAIL. Open end GOLD 5/16" FLAT HEAD SCREW (4 used in this step) Edge with CAM DOWELS Edge with CAM DOWELS Open end www.sauder.com/services 418705 Page 7...
  • Page 8 MOLDINGS (L, M, and N). Some assembly (and snacks) required. Use your hammer to tap the MOLDING CONNECTORS (19F) into the notches in the MOLDINGS. Flat end Unfi nished surface Unfi nished surface Flat end Unfi nished surface Page 8 418705 www.sauder.com/services...
  • Page 9 SILVER 1-1/8" FLAT HEAD SCREWS (10S). NOTE: Do not overtighten the SCREWS into the TOP. å SILVER 1-1/8" FLAT HEAD SCREW (7 used in this step) Do not overtighten the SCREWS (10S). Long curved edge www.sauder.com/services 418705 Page 9...
  • Page 10 Tighten Risk of damage or Arrow injury. HIDDEN CAMS must be completely Maximum Arrow tightened. HIDDEN 210 degrees CAMS that are not completely tightened may loosen, and parts may separate. To Minimum completely tighten: 190 degrees Page 10 418705 www.sauder.com/services...
  • Page 11 NOTE: Be sure the METAL PIN in the BRACE inserts into the å Minimum hole in the LEFT END. 190 degrees S u r f a c i t h H I D D E N Edge without HIDDEN CAM www.sauder.com/services 418705 Page 11...
  • Page 12 NOTE: Be sure the METAL PIN in the BRACE inserts into å the hole in the RIGHT END. Minimum 190 degrees Edge with CAM DOWELS i t h o f a c S u r D E N H I D Page 12 418705 www.sauder.com/services...
  • Page 13 Step Step 8 Fasten the MOLDINGS (M and N) to the ENDS (A and B). å Tighten four HIDDEN CAMS. Maximum Arrow 210 degrees Minimum 190 degrees www.sauder.com/services 418705 Page 13...
  • Page 14 B). Use four GOLD 5/16" FLAT HEAD SCREWS (3S). NOTE: The parts are marked "CABINET RIGHT" and å "CABINET LEFT" for easy identifi cation. GOLD 5/16" FLAT HEAD SCREW (4 used in this step) Roller end Page 14 418705 www.sauder.com/services...
  • Page 15 Fasten the BASES (I and J) to the ENDS (A and B). Use å four BLACK 1-1/4" FLAT HEAD SCREWS (7S). Don't worry. It isn't Rome. This can be built in a day. BLACK 1-1/4" FLAT HEAD SCREW (4 used in this step) Flat edge Flat edge www.sauder.com/services 418705 Page 15...

  • Page 16: Black 9/16" Large Head Screw

    Fasten the BASE (H) to the ENDS (A and B) and BOTTOM (D). å Use fi ve BLACK 9/16" LARGE HEAD SCREWS (1S) through the METAL BRACKETS and into the BASE. BLACK 9/16" LARGE HEAD SCREW (10 used in this step) Flat edge (5 used) Page 16 418705 www.sauder.com/services...
  • Page 17 BACK fastened. The unit may collapse. Push on opposite corners of your unit if needed to make it "square". Fasten the BACK (F) to your unit using the NAILS (1N). å NAIL (24 used in this step) www.sauder.com/services 418705 Page 17...
  • Page 18 Fasten the SHELF (E) to the SHELF MOLDING (O). å Tighten two HIDDEN CAMS. Surface with more holes SILVER 3/4" MACHINE SCREW (1 used for the KNOB) These holes are closer to this edge. Maximum Arrow 210 degrees Minimum 190 degrees Page 18 418705 www.sauder.com/services...

  • Page 19: Brown 1" Flat Head Screw

    Fasten the DRAWER SLIDES (R and S) to the SHELF (E). å Use four BROWN 1" FLAT HEAD SCREWS (18S). NOTE: The parts are marked "DRAWER RIGHT" and å "DRAWER LEFT" for easy identifi cation. BROWN 1" FLAT HEAD SCREW (4 used in this step) www.sauder.com/services 418705 Page 19...

  • Page 20: Black 1-9/16" Flat Head Screw

    Fasten the DRAWER BACK (D163) to the DRAWER Fasten the DRAWER BRACE (M67) to the DRAWER å å SIDES (D24 and D25) and DRAWER BRACE (M67). Use FRONT (K). Tighten one HIDDEN CAM. five BLACK 1-9/16" FLAT HEAD SCREWS (30S). Page 20 418705 www.sauder.com/services...

  • Page 21: Gold 5/16" Flat Head Screw

    Screw head - turn CAM to line up holes in the SLIDES with holes in DRAWER SIDES Open end BLACK 7/8" MACHINE SCREW (2 used for the PULL) GOLD 5/16" FLAT HEAD SCREW (4 used in this step) www.sauder.com/services 418705 Page 21...
  • Page 22 The drawer will push in hard until it is all the way in, then it will slide in and out easier. 40 lbs. 10 lbs. 20 lbs. 30 lbs. Page 22 418705 www.sauder.com/services...
  • Page 23 #3. The higher the screw in the oblong hole, the higher your drawer front will be. The lower the screw, the lower the drawer front. www.sauder.com/services 418705 Page 23...

  • Page 24: Liste De Pièces

    EXTRÉMITÉ DROITE ..........1 GLISSIÈRE DROITE D'ÉLÉMENT .....1 pour future référence. EXTRÉMITÉ GAUCHE ..........1 GLISSIÈRE GAUCHE D'ÉLÉMENT ....1 Pour contacter Sauder en ce qui concerne cet DESSUS ................1 COULISSE DROITE DE TIROIR ......1 élément, faire référence DESSOUS ................1 COULISSE GAUCHE DE TIROIR ......1...
  • Page 25 Escamotables doivent être serrés à bloc. Les Excentriques CONSOLES EN MÉTAL et dans le SOCLE. Escamotables que ne sont pas serrées à bloc peuvent desserrer et les pièces peuvent séparer. Pour serrer à bloc, faire tourner l'excentrique escamotable de 210 degrés. www.sauder.com/services 418705 Page 25...
  • Page 26 4 Fixer l'ARRIÈRE DE TIROIR (D163) aux CÔTÉS DE TIROIR (D24 et D25) et à l’ENTRETOISE DE TIROIR (M67). Utiliser cinq VIS Ceci complète l'assemblage. Nettoyer à l’ a ide d’une encaustique TÊTE PLATE 40 mm NOIRES (30S). pour meubles ou d’un chiff on humide. Essuyer. Page 26 418705 www.sauder.com/services...

  • Page 27: Lista De Partes

    (JUEGO DE EXTENSIÓN SE MUESTRA POR SEPARADO) et conserver le livret RIEL DE EXTENSIÓN ..........2 pour future référence. EXTREMO IZQUIERDO ..........1 Pour contacter Sauder CORREDERA DE EXTENSIÓN ......2 PANEL SUPERIOR ............1 en ce qui concerne cet 10A EXCÉNTRICO DE CORREDERA .......2 FONDO .................1...
  • Page 28 Escondidos deben apretarse completamente. Los Excéntricos a través de los SOPORTES DE METAL y en la BASE. Escondidos que no se aprieten completamente se afl ojarán y las partes pueden separarse. Para apretar completamente, atornille el excéntrico escondido 210 grados. Page 28 418705 www.sauder.com/services...
  • Page 29 D25) y a la RIOSTRA DE CAJÓN (M67). Utilice cinco TORNILLOS NEGROS DE CABEZA PERDIDA de 40 mm (30S). Esto completa el ensamblaje. Limpie con su pulimento para muebles preferido o un paño húmedo. Seque con un paño. www.sauder.com/services 418705 Page 29...
  • Page 30 Además, el peso y la ubicación del tubo de imagen tienden a causar la inestabilidad de televisores y son propensos a inclinarse hacia adelante. Page 30 418705 www.sauder.com/services...

  • Page 31: Garantie Limitée De 5 Ans

    GARANTIE LIMITÉE DE 5 ANS 1. Sauder Woodworking Co. (Sauder®) off re une couverture de garantie limitée à l’ a cheteur 4. La présente garantie ne s’ a pplique qu’ a ux défauts garantis qui se produisent pour initial du présent produit pendant une période de cinq ans à...
  • Page 32 Dear Valued Customer: So, how did it go? Thanks so much for choosing Sauder® furniture. I hope the Set a world record for speed? purchase and assembly process was a positive experience Feeling good about yourself? and you feel good about the furniture you just built. If you Nice.

Table des Matières