Publicité
Liens rapides
It allows to control motors or resistive loads with a maximum of 1500 W and a minimum of 50 W. It does not admit
inductive loads such as coils, transformers, low consumption light bulbs such as PL or LED, fluorescent.
POWER SUPPLY : 230 V. AC. 50 Hz Connect a network cable with plug, capable of withstanding a minimum of 10 A.
in the INPUT AC input in the terminals marked as line "L" and neutral "N". Install a switch and a 10A fuse for protection
and safety according to CE standards.
Control (input) : The regulation can be controlled or adjusted by means of a 10K linear potentiometer or by voltage
level, through an external signal between 0 and 10 V. In no case both inputs at the same time. The length of the
cables should be as short as possible. If it is greater than 50 cm, use shielded cable.
External signal 0-10 V.D.C. The connection must be made on the "D.C. Control", respecting the indicated polarity.
External potentiometer. Indicated as "Ext. Pot.", this input accepts only 10K ohm linear potentiometers. Terminal "A"
corresponds to the minimum end of the potentiometer, "B" to the shaft input and "C" to the maximum end.
Considerations : Mount in a well-ventilated plastic box, install away from high temperatures and liquid ingress.
Change of the fuse: The circuit has a fuse for the protection of the control electronics, this fuse is independent of the
one that must be installed with the power switch. To change this fuse you must first disconnect the 230V input. AC
from the circuit, remove the protector and replace the fuse with one of the same value. Do not use fuses of different
intensity.
Regulator AC 1500 W
Régulateur AC 1500 W
Regulador AC 1500 W
Regulador AC 1500 W
Technical characteristics
Input Voltage : 230 V. AC. 50 Hz
Load regulation : 0 al 100%. 230 V.A.C.
Minimum load : 50 W.
Maximum load : 1500W
Regulatory control : Input signal 0-10 V.D.C. or potentiometer
10K ohms.
Setting minimum : Variable potentiometer in the circuit.
Operating indicator Leds : Power, power output
Maximum section conductors : 4 mm..
Weight : 222 gr.
Measures : 121 x 107 x 46mm.
Din rail : C-7589
Regulations : Electromagnetic Compatibility Directive
89/336/EEC and its amendments 32/31/CEE y 93/68/CEE.
RoHS free
www.cebek.com
-
R-28
sat@fadisel.com
Publicité
Manuels Connexes pour CEBEK R-28
Sommaire des Matières pour CEBEK R-28
- Page 1 Regulator AC 1500 W Régulateur AC 1500 W Regulador AC 1500 W Regulador AC 1500 W R-28 Technical characteristics Input Voltage : 230 V. AC. 50 Hz Load regulation : 0 al 100%. 230 V.A.C. Minimum load : 50 W.
- Page 2 R-28 Il permet de contrôler des moteurs ou des charges résistives avec un maximum de 1500 W et un minimum de 50 W. Il n'admet pas de charges inductives telles que bobines, transformateurs, ampoules basse consommation telles que PL ou LED, fluorescentes.
- Page 3 R-28 Control (entrada) : El control o ajust de la regulació es pot fer mitjançant un potenciòmetre lineal de 10K o per nivell de tensió, a través d'un senyal extern entre 0 i 10 V. En cap cas les dues entrades alhora. La longitud dels cables haurà...
- Page 4 R-28 CONFIGURACIÓ DIPS : DIP 1 regulació per 0-10 V, DIP 2 regulació per potenciòmetre, DIP 3 sense ús DIP 4 regulació de 0 a 230 VAC o de 230 a 0 V. Nota. Cada vegada que canvieu la posició d'algun dels dips, heu de desconnectar i tornar a connectar l'alimentació...
- Page 5 R-28 Ajuste mínimo : El potenciómetro como “MIN LEVEL .” permite, mediante su regulación, ajustar el punto mínimo de activación de la carga. Regulación : En la regulación por señal 0-10V., si se sitúa el dip 4 en posición Off, la salida proporcionará tensión de 0 a 230 V., en proporción directa al valor de la señal de control.
- Page 6 R-28 www.cebek.com sat@fadisel.com...