GE JGP328 Instructions D'installation
Masquer les pouces Voir aussi pour JGP328:

Publicité

Les langues disponibles

Les langues disponibles

Liens rapides

Installation
Instructions
Questions? Call 800.GE.CARES (800.432.2737) or Visit our Website at: ge.com
In Canada, call 1.800.361.3400 or Visit our Website at: www.geappliances.ca
IN THE COMMONWEALTH OF
MASSACHUSETTS:
• This product must be installed by a
licensed plumber or gas fitter.
• When using ball-type gas shut-off valves,
they shall be the T-handle type.
• A flexible gas connector, when used, must
not exceed 3 feet.
BEFORE YOU BEGIN
Read these instructions completely
and carefully.
IMPORTANT
instructions for local inspector's use.
IMPORTANT
governing codes and ordinances.
• Note to Installer – Be sure to leave these
instructions with the Consumer.
• Note to Consumer – Keep these
instructions for future reference.
• Product failure due to improper installation
is not covered under the Warranty.
WARNING
be properly grounded.
IMPORTANT
appliance shall be conducted according to
the manufacturer's instructions.
• Proper installation is the responsibility
of the installer and product failure due to
improper installation is NOT covered under
warranty.
WARNING
electrical power at the main circuit breaker
or fuse box before installing.
31-10613-3
(11-06 JR)
30" Sealed Gas Cooktop
JGP328, JGP330, JGP933,
JGP940, JGP945
— Save these
— Observe all
— This appliance must
— Leak testing of the
— Disconnect all
FOR YOUR SAFETY:
WARNING
in this manual is not followed exactly, a fire,
explosion or gas leak may result causing
property damage, personal injury or death.
Do not store or use gasoline or other
flammable vapors and liquids in the vicinity
of this or any other appliance!
WHAT TO DO IF YOU
SMELL GAS:
• Do not try to light any appliance. Do not
touch any electrical switch; do not use any
phone in your building.
• Immediately call your gas supplier from a
neighbor's phone. Follow the gas supplier's
instructions.
• If you cannot reach your gas supplier, call
the fire department.
Installation and service must be performed
by a qualified installer, service agency or
the gas supplier.
This cooktop has been design certified
by CSA International. You'll find safety
precautions in your Owner's Manual.
Read them carefully.
• Installation of this cooktop must conform
with local codes or in the absence of local
codes with the National Fuel Gas Code,
ANSI Z223.1/NFPA 54–Latest edition.
• Be sure your cooktop is installed properly
by a qualified installer or service technician.
• To eliminate reaching over surface burners,
cabinet storage above burner should be
avoided.
• Do not install the unit near an outside door
or where a draft may affect its use.
1
— If the information

Publicité

Table des Matières
loading

Sommaire des Matières pour GE JGP328

  • Page 1 Installation 30″ Sealed Gas Cooktop Instructions JGP328, JGP330, JGP933, JGP940, JGP945 Questions? Call 800.GE.CARES (800.432.2737) or Visit our Website at: ge.com In Canada, call 1.800.361.3400 or Visit our Website at: www.geappliances.ca FOR YOUR SAFETY: IN THE COMMONWEALTH OF MASSACHUSETTS: WARNING —...
  • Page 2: Important Safety Instructions

    Installation Instructions IMPORTANT SAFETY INSTRUCTIONS ELECTRICAL REQUIREMENTS PARTS INCLUDED This appliance must be supplied with the proper voltage and frequency and connected to an individual, properly grounded branch circuit, protected by a circuit breaker or fuse 2 Screws Foam Tape having amperage as noted on the rating plate.
  • Page 3: Pre-Installation Checklist

    Installation Instructions PRE-INSTALLATION CHECKLIST When preparing cooktop opening, Remove Installation Instructions from make sure the inside of the cabinet and literature pack and read them carefully the cooktop do not interfere with each before you begin. other. (See section on preparing the Be sure to place all literature, Use and opening.) Care, Installations, etc.
  • Page 4: Preparing The Opening

    Installation Instructions PREPARING THE OPENING MAINTAIN THE FOLLOWING RECOMMENDED GAS SUPPLY MINIMUM CLEARANCE LOCATION FROM BACKWALL DIMENSIONS 1” Min. From Backwall 13″ MAX. Depth of unprotected overhead cabinets 6″ MIN. clearance from Recommended 3 3/4 MIN. cutout to side wall on gas supply the right of the unit location...
  • Page 5 Installation Instructions INSTALLING THE COOKTOP UNIT LOCATE ELECTRICAL OUTLET LOCATE MOUNTING PARTS AND GAS SHUT-OFF VALVE Remove the hold down brackets from the literature package. BENEATH CABINET NEVER REUSE OLD CONNECTORS WHEN INSTALLING Shut Off Electrical Valve THIS UNIT. Outlet 12″ Below Countertop ATTACH BRACKETS TO...
  • Page 6 Installation Instructions INSTALLATION—GAS CONNECTIONS PROVIDE ADEQUATE INSTALL REGULATOR ONTO GAS SUPPLY BURNER BOX BOTTOM This cooktop is designed to operate on Screw the natural gas at 4″ of water column manifold regulator onto pressure and 7″ of water column (W.C.) the burner box supply pressure.
  • Page 7 Installation Instructions CHECK FOR LEAKS INSTALLATION OVER BUILT-IN OVEN Before testing for leaks, make sure all burner knobs are in the OFF position. See built-in oven installation for complete installation instructions. After connecting the cooktop to gas, check system for leaks with a manometer. If a manometer is not available, turn the gas supply on to the cooktop and use a liquid leak detector at all joints and connections...
  • Page 8: Important

    Installation Instructions Installation Instructions INSTALLATION—ELECTRICAL CONNECTIONS WARNING ELECTRICAL SUPPLY AND — Disconnect all OUTLET electrical power at the main circuit breaker or fuse box before installing. An adequate electrical supply and outlet must be used to operate the electrical parts of your cooktop.
  • Page 9 Installation Instructions CAUTION: USAGE SITUATIONS WHERE Attaching the adaptor ground terminal to the wall receptacle cover screw APPLIANCE POWER CORD does not ground the appliance unless the WILL BE DISCONNECTED screw is metal, and not insulated, and the wall INFREQUENTLY receptacle is grounded through the house wiring.
  • Page 10: Cooktop Burners

    Installation Instructions COOKTOP BURNERS ASSEMBLING THE COOKTOP Make sure the Burner cap pins in the burner BURNERS heads match the The electrode of the spark igniter is exposed. burner base Be careful not to push any cooktop controls indentations and Burner head while the top of the burner is removed.
  • Page 11: The Burner Flames

    Installation Instructions CHECK IGNITERS THE BURNER FLAMES Operation of the electric igniters should be Turn each burner on. Flames should be blue checked after the cooktop and supply line in color with no trace of yellow. The burner have been carefully checked for leaks and flames should not flutter or blow away from the cooktop has been connected to the the burner.
  • Page 12: Operation Checklist

    Installation Instructions OPERATION CHECKLIST Make sure all controls are left in the OFF When ordering parts, always include the position. Check to be sure the cooktop is serial number, model number and a code in the UNLOCKED position (on models letter to ensure proper replacement parts.
  • Page 13 Installation Instructions MAKING THE LP CONVERSION SAFETY INFORMATION YOU ADJUST YOUR COOKTOP FOR SHOULD KNOW USE WITH LP GAS The pressure regulator and burner orifices Disconnect all electrical power, at the are set for natural gas. To use Propane Gas, main circuit breaker or fuse box.
  • Page 14 Installation Instructions MAKING THE LP CONVERSION (CONT.) CHANGE COOKTOP BURNER CHANGE COOKTOP BURNER ORIFICES ORIFICES (CONT.) Remove the top NOTE: On most burners, grates, burner caps, the orifices have a spring- Retainer and burner heads. loaded retaining ring Ring Remove This around the hex head to Remove the spark...
  • Page 15 Left Rear Left Front Right Front These marks denote the precise location of Model Orifice Orifice Orifice each orifice to the cooktop burner. JGP328 JGP330 JGP933 JGP940 18,000 BTU/HR Burner (on some models) JGP945 Replace: With: ➔ 108X L...
  • Page 16 Installation Instructions MAKING THE LP CONVERSION (CONT.) ADJUST BURNER FLAMES Make the adjustment by slowly turning the screw until flame appearance is Turn all burners full on and check the correct. flames. They should be blue in color with Testing Flame Stability: some yellow tipping at the ends of the flame.
  • Page 17: Avant De Commencer

    Instructions Table de cuisson scellée au gaz de 76 cm (30″) d’installation JGP328, JGP330, JGP933, JGP940, JGP945 Questions? Appelez le Centre de réponse 1.800.361.3400 ou visitez notre site Web à l’adresse : www.electromenagersge.ca AVANT DE COMMENCER POUR VOTRE SÉCURITÉ Avant de commencer, lisez attentivement la AVERTISSEMENT —...
  • Page 18: Instructions Importantes De Sécurité

    Instructions d’installation INSTRUCTIONS IMPORTANTES DE SÉCURITÉ La conception de votre table de cuisson a été PIÈCES COMPRISES approuvé par l’ACNOR International. Vous trouverez des précautions à prendre en matière de sécurité dans votre Guide d’utilisation et de soins. Lisez-les attentivement. 2 vis Bandes de mousse 2 Supports de...
  • Page 19: Liste De Vérification Avant Installation

    Instructions d’installation LISTE DE VÉRIFICATION AVANT INSTALLATION Pour préparer l’ouverture de la surface Enlevez les instructions d’installation de cuisson, vous devez vous assurer de la trousse de documentation et que l’intérieur de l’armoire ne touche lisez-les soigneusement avant de pas la table de cuisson (consultez la commencer.
  • Page 20: Préparation De L'ouverture

    Instructions d’installation PRÉPARATION DE L’OUVERTURE VOUS DEVEZ RESPECTER LES EMPLACEMENT DÉGAGEMENTS MINIMAUX RECOMMANDÉ DE SUIVANT L’ALIMENTATION DE GAZ À PARTIR DU MUR ARRIÈRE Profondeur max de 33 cm (13″) des armoires en surplomb non protégées Dégagement min. de 2.5 cm (1″) min. du mur arrière 15 cm (6″) découpage 3 3/4 MIN.
  • Page 21: Installation La Unité De La Table De Cuisson

    Instructions d’installation INSTALLATION LA UNITÉ DE LA TABLE DE CUISSON PLACEZ LA PRISE TROUVEZ LES PIÈCES DE D’ALIMENTATION MONTAGE ÉLECTRIQUE ET LE ROBINET Retirez les supports de fixation de la trousse de documentation. D’ALIMENTATION DE GAZ AU-DESSOUS DE L’ARMOIRE N’UTILISEZ JAMAIS DES RACCORDS Robinet USAGÉS POUR...
  • Page 22: Installation-Branchement Du Gaz

    Instructions d’installation INSTALLATION—BRANCHEMENT DU GAZ FOURNISSEZ UN BON INSTALLEZ LE RÉGULATEUR APPROVISIONNEMENT EN BAS DE LA BOÎTE DE EN GAZ BRÛLEURS Cette table de cuisson est conçue pour Vissez le fonctionner au gaz naturel à une pression de régulateur dans tubulure d’admission de 4 po.
  • Page 23 Instructions d’installation VÉRIFIEZ QU’IL N’Y A PAS DE INSTALLATION SUR UN FOUR FUITE ENCASTRÉ Avant de vérifier qu’il n’y a pas de fuite, Consultez l’installation du four encastré pour assurez-vous que tous les boutons de y trouver les instructions d’installation. brûleurs soient en position OFF (arrêt).
  • Page 24: Installation-Raccords Électriques

    Instructions d’installation INSTALLATION—RACCORDS ÉLECTRIQUES AVERTISSEMENT ALIMENTATION ÉLECTRIQUE — ET PRISE Débranchez tout courant électrique au niveau du disjoncteur de la maison ou de la boîte à Vous devez utiliser une bonne alimentation fusibles avant d’installer. électrique et une bonne prise pour faire fonctionner les éléments électriques de votre table de cuisson.
  • Page 25 Instructions d’installation INSTALLATION—RACCORDS ÉLECTRIQUES ( SUITE) MISE EN GARDE : SITUATION D’UTILISATION OÙ LE Si vous fixez la broche de mise à la terre de l’adaptateur CORDON D’ALIMENTATION D’UN à une vis du couvercle de la prise murale, APPAREIL ÉLECTROMÉNAGER cela ne met pas à...
  • Page 26: Brûleurs De La Table De Cuisson

    Instructions d’installation BRÛLEURS DE LA TABLE DE CUISSON Capuchon de brûleur ASSEMBLEZ LES BRÛLEURS Assurez-vous que les broches des DE LA TABLE DE CUISSON têtes de brûleur L’électrode de l’allumeur est exposée. Faites correspondent attention de ne pas pousser un contrôle de la Tête de brûleur aux creux de la table de cuisson quand le haut du brûleur est...
  • Page 27: Vérifiez Les Allumeurs

    Instructions d’installation VÉRIFIEZ LES ALLUMEURS ALLUMAGE DES BRÛLEURS Vous devez vérifier le fonctionnement des Allumage de la table de cuisson – Quand allumeurs électriques après vous être vous mettez le bouton de la table de cuisson soigneusement assuré que la table de cuisson en position LITE (allumage), l’allumeur fait et la ligne d’approvisionnement n’ont pas de une série d’étincelles (crépitement) pour...
  • Page 28: Les Flammes Du Brûleur

    Instructions d’installation BRÛLEURS DE LA TABLE DE CUISSON (SUITE) LES FLAMMES DU BRÛLEUR GRILLES DE BRÛLEUR Les quatre grilles de brûleur sont conçues Allumez chaque brûleur. Les flammes doivent pour leur emplacement particulier. Pour être bleu sans trace de jaune. Les flammes du obtenir une stabilité...
  • Page 29: Conversion Au Gaz Propane

    Instructions d’installation CONVERSION AU GAZ PROPANE RENSEIGNEMENTS RELATIFS AJUSTEZ VOTRE PLAQUE DE À LA SÉCURITÉ QUE VOUS CUISSON À UN USAGE AU DEVEZ CONNAÎTRE GAZ PROPANE Les diaphragmes du régulateur de pression et du Débranchez tout le courant électrique, au brûleur sont réglés pour le gaz naturel.
  • Page 30: Changez Les Diaphragmes Des Brûleurs De La Table De Cuisson (Suite)

    Instructions d’installation CONVERSION AU GAZ PROPANE (SUITE) CHANGEZ LES DIAPHRAGMES CHANGEZ LES DIAPHRAGMES DES BRÛLEURS DE LA TABLE DES BRÛLEURS DE LA TABLE DE CUISSON DE CUISSON (SUITE) Enlevez les grilles du NOTE : Sur la plupart des haut, les capuchons brûleurs, les diaphragmes Bague de de brûleur et les têtes...
  • Page 31 Chaque diaphragme indique une série Modèle gauche gauche droit de signes gravés (I, II, III, X ou rien) en JGP328 haut. JGP330 Ces signes indiquent l’emplacement JGP933 précis de chaque diaphragme sur le JGP940 brûleur de la table de cuisson.
  • Page 32 Instructions d’installation CONVERSION AU GAZ PROPANE (SUITE) AJUSTEZ LES FLAMMES DES Continuez à ajuster en tournant lentement la vis jusqu’à ce que les BRÛLEURS flammes soient normales. Allumez tous les brûleurs au maximum Essai de stabilité de la flamme : et vérifiez les flammes.

Ce manuel est également adapté pour:

Jgp330Jgp933Jgp940Jgp945

Table des Matières