Publicité
Les langues disponibles
Les langues disponibles
CONTROL PANEL NE293_15-RA
GB
CONTROLS:
Push button with warning light for turning
INTERNAL LIGHTS on or off
Push button with warning light for turning
INTERNAL LIGHTS on or off
Symbol with warning light to indicate that the
control panel and the output F12 are power on or off
See also CONSUMPTION and the nocturnal settings function
SCREENS:
The warning light goes on when the 230V mains is connected
The warning light goes on when
of the 230V mains when the two batteries are in parallel verifing before the battery service voltage
The warning light goes on when the recycling tank R1 is full.
Press the push button repeatedly for viewing:
-The voltage on the starter battery B1
-The voltage on the service battery B2
-The level percentage % (0, 25, 50, 75, 100) of the reservoir S1
If S1 is empty, the display flashes.
If the reservoir is wrongly connected, the display will show "
The screen remains active for approx. 30 seconds.
ALARMS:
Batteries: Car battery (B1) less than 11,8V or Service battery (B2) less than 10V.
In this case there is a bleep (if enabled) and the flashing battery symbol that have generated the alarm
(for the first 30 seconds you see the value)
Tanks:
Tank S1 empty
In this case there is a bleep (if enabled) and the flashing symbol tank (for the first 30 seconds you see the value)
:
This symbol appears on the display to indicate that the step is open with the vehicle in motion.
In this case a continuous acoustic alarm sounds. If the panel is off, only the continuous acoustic alarm is activated.
:
This symbol appears on the display to indicate that the 230V mains supply on with the vehicle in motion.
In this case a continuous acoustic alarm sounds. If the panel is off, only the continuous acoustic alarm is activated.
:
This symbol appears when there is an error communicating with NE196 shunt.
The control panel beeps whenever the vehicle ignition switch is in the "MAR" position (signal + shunt key), even when the
panel is off. The purpose is to test operation of the acoustic signal.
SETTING:
Hold down the (
) push button for over 3 seconds to disable (display shows "
confirmation beep button pressed, and alarm buzzers.
Hold down the (
) push button for over 3 seconds to disable (display shows "
ignition of the external light for 5 seconds with the vehicle remote control (TLC), even when the panel is off.
Hold down the (
) push button for over 3 seconds to disable (display shows "
ignition of the external light for 30 seconds with the vehicle remote control (TLC), even when the panel is off.
Hold down the (
) push button for over 3 seconds to enable the night function. The display shows first the initials "
and then all the symbols go out; only a dot remains on the screen. Hit any key to re-illuminate the symbols. When the night
function is operative alarms are not indicated but when the service battery voltage drops below 10V for over 3 minute the
switching off of the control panel is shown.
CONSUMPTION:
To turn on the control panel you must touch for 2 sec. a button any. The display will show the panel firmware version for one
second and then the firmware version for the shunt in use for a further second.
On stand by (no active controls) the control panel with shunt NE196 consumes a total of approx 83mA. When the
key (
) is pressed for 5 sec. the control panel turns itself off and total consumption is reduced to just 5mA.
If the service battery voltage drops below 10V, after 3 minute the control panel turns itself off, together with all live parts.
CONNECTIONS:
The back of the panel has a connector for serial connection (JP4).
the vehicle engine is running and the parallel batteries is active or in the presence
.
.
4
Push button with warning light for turning
PUMP on or off
Push button with warning light for turning
AUX on or off
.
".
" ) or enable (display shows "
") or enable (display shows "
") or enable (display shows "
GB
") the
")
")
"
Publicité
