Autoselect - Black & Decker FSMH1300FX Mode D'emploi

ENGLISH
Assembly
Warning! Before attempting any of the following in-
@
structions, make sure that the appliance is switched
off and unplugged and the appliance is cold and
does not contain any water.
g the floor extension to the floor cleaning head
Attachin
(Fig. A)
Push the floor extension (8) firmly into the floor cleaning
u
head (9) making sure it clicks securely into place.
g the hand held hand held steam unit to the floor
Attachin
extension (Fig. B)
Push the hand held hand held steam unit firmly onto the
u
floor extension (8) making sure it sits correctly over the
interface (6) and clicks securely into place.
Warning! Inspect the seal between the connection point
on the hand held steam cleaner and the floor extrension (8)
before each use. If the seal malfunctions or is damaged,
please contact your nearest authorised repair agent. Do not
use the appliance.
Removing the hand held steam unit
Push the release button (7) on the floor extension (8) and
u
lift the hand held steam unit off the interface (6).
Attaching a cleaning pad (Fig. C)
Replacement cleaning pads are available from your
BLACK+DECKER dealer :- (cat no. FSMP20-XJ).
Place a cleaning pad (10) on the floor with the velcro 'loop'
u
side facing up.
Lightly press the steam mop down onto the cleaning pad
u
(10).
Caution! Never leave the steam mop in one spot on any
surface for any period of time. Always place the steam mop
supported in the upright position when stationary and make
sure the steam mop is turned off when not in use.
Removing a cleaning pad
Caution! Always wear suitable shoes when changing the
cleaning pad on your steam mop.
Do not wear slippers or open toed footwear.
Return the steam mop to the upright position and turn the
u
steam mop 'OFF'.
Wait until the steam mop cools down (approximately 5
u
minutes).
Lift the steam mop away from the cleaning pad freeing it
u
from the velcro fastening by putting weight on the cleaning
pad removal tab (11).
Caution! Never leave the steam mop in one spot on any
surface for any period of time.
8
(Original instructions)
Always place the steam mop supported in the upright position
when stationary and make sure the steam mop is turned off
when not in use.
Filling the water tank (Fig. D)
Note! Fill the water tank with clean tap water (Do not use any
additives or chemicals).
Note! In areas of hard water, the use of de-ionised water is
recommended.
Open the filler cap (4) by flipping it up.
u
Fill the water tank with water (Do not use any additives or
u
chemicals).
Warning! When filling, maintain in a horizontal position.
Warning! Your water tank has a 0.5 litre capacity. Do not over
fill the tank.
Close the filler cap (4).
u
Note! Ensure the filler cap is firmly secured.
Use
Important! This unit will kill 99.9% of bacteria and germs
when used in accordance with the instructions in this manual
and with the micro fibre pads fitted and a continuous run time
of 90 seconds.
(Fig. F)
Switching on and off
To switch the appliance on, press the ON/Off switch (1).
u
It takes approximately 15 seconds for the steam mop to
heat up.
To switch the appliance off, press the ON/Off switch (1).
u
Caution! Never leave the steam mop in one spot on any
surface for any period of time.
Always place the steam mop supported in the upright position
when stationary and make sure the steam mop is turned off
when not in use.
Caution! Always empty the steam mop after use.
Note! When first filled or after running dry, it can take up to 45
seconds for steam to be produced.

Autoselect

TM Technology (Fig. E)
This steam mop is fitted with an Autoselect
shows various cleaning applications. They are used to select
the correct operating mode for your particular cleaning
operation.
Using Autoselect TM , choose from one of the following
applications by turning the Autoselect
required setting is selected.
dial (2) which
TM
dial (2) until the
TM