G Eneral Notes On Safety; Se Of The Machine For Purposes For Which It Is Intended; I Ncorrect Use; Ec Declaration Of Conformity - SUHNER ABRASIVE ASC 9 Dossier Technique

1. Notes on Safety
1.1 g
enerAl notes on sAfety
This technical document is applicable for the machine
UPG 5-R. The machine may only be handled by person-
nel who are qualified.
Hold power tools by insulated gripping surfaces when
performing an operation where the cutting tool may con-
tact hidden wiring or its own cord. Contact with a «live»
wire will make exposed metal parts of the tool «live» and
shock the operator.
WARNING Read all safety warnings and all in-
structions. Failure to follow the warnings and in-
structions may result in electric shock, fire and/or
serious injury.
Save all warnings and instructions for future refer-
ence.
1.2 u
se of the mAchine for PurPoses for
which it is intended
The machine is intended for the grinding and deburring
of metal with hard-metal milling cutters and plastic-resin
bonded forming abrasive wheels without the use of water.
The machine is designed exclusively for a 2-hand appli-
cation.
1.3 i
ncorrect use
All uses other than those described under section
1.2 are regarded as incorrect use and are there-
fore not admissible.
1.4 ec
declArAtion of conformity
Translations of the «EG-Koformitätserklärung (Original)».
Otto Suhner GmbH of Trottäcker 50, D-79713 Bad Säck-
ingen, hereby declares under sole responsibility that the
product with the serial or batch no. (see reverse side) com-
plies with the requirements under the Directive 2014/30/
EU, 2006/42/EC, 2011/65/EU. Applied standards: EN ISO
12100, EN 60745, EN 55014-1, EN 55014-2, EN 61000-
3-2, EN 61000-3-3. Document Agent: T. Fischer. D-Bad
Säckingen, 01/2020.
T. Fischer/Division manager
2. Commissioning
2.1 P
rior to tAKing the mAchine into serVice
The battery pack is delivered in a
partially charged state. The battery
pack can deliver its full power out-
put when it is first fully charged in the sup-
plied charging unit before it is used for the first time.
Check that the battery pack is clean and undamaged. Do
not use damaged battery packs.
22
Check the grinding belt before use.
The driver roller must be installed centrally and aligned to
the stop.
Under no circumstances must the grinding belt exceed
the max permitted speed.
Observe national regulations.
Take protective measures when dust can develop dur-
ing working that is harmful to one's health, cumbustible
or explosive. Wear a dust mask and work with dust/chip
extraction when connectable.
2.2 t
AKing the mAchine into serVice
2.2.1 i
nsert the BAttery PAcK
Insert the battery pack until it engages audibly.
2.2.2 t /t
urn on urn off
The switch must be at the OFF position, i.e. the «0» is
visible. To switch ON the tool, press the switch, and push
it forwards until it engages audibly, i.e. the «1» becomes
bisible. Press the ON/OFF swith to trigger the blocking
and the machine shuts down.
2.3 r

Ating dAtA

Voltage
No-load speed
Max. tool Ø
Sound pressure level EN 60745
Vibration EN 60745
Weight
The specified vibration value was measured with a
standardised test procedure. It can be used to
compare products or to make an initial assess-
18V DC
9000min
-1
55mm
79.1dB(A), K=3dB
2.8m/s , K=1.5m/s
2 2
2.200kg