Publicité
Liens rapides
DIR 1000719R0905 Version 01 - 140G-G-OSB, 140G-K-OSB, 140G-M-OSB, 140G-N-OSB
Variable depth operating mechanism-support bracket for 140G-G,-K,-M,-N
Supporto asta maniglia rotante rinviata
Installation - Installazione - Instalación
Instalação -
WARNING:
To prevent electrical shock, disconnect from power source before
installing or servicing. Install in suitable enclosure. Keep free from contaminants.
(Follow NFPA70E requirements).
AVVERTENZA: Per prevenire infortuni, togliere tensione prima dell'installazione o
manutenzione. Installare in custodia idonea. Tenere lontano da contaminanti.
(Seguire i requisiti NFPA70E).
WARNUNG:
Vor Installations- oder Servicearbeiten Stromversorgung zur
Vermeidung von elektrischen Unfällen trennen. Die Geräte müssen in einem
passenden Gehäuse eingebaut und gegen Verschmutzung geschützt werden. (Befolgen
Sie die Anforderungen nach NFPA70E).
AVERTISSEMENT:
Avant le montage et la mise en service, couper l'alimentation
secteur pour éviter toute décharge. Prévoir une mise en coffret ou armoire appropriée.
Protéger le produit contre les environnements agressifs. (Vous devez respecter la
norme NFPA70E).
ADVERTENCIA: Desconéctese de la corriente eléctrica, antes de la instalación o
del servicio, a fin de impedir sacudidas eléctricas. Instálelo en una caja apropiada.
Manténgalo libre de contaminantes. (Cumpla con los requisitos NFPA70E).
ATENÇÃO: Para evitar choques, desconectar da corrente elétrica antes de fazer a
instalação ou a manutenção. Instalar em caixa apropriada. Manter livre de
contaminantes. (Cumpra as exigências da norma NFPA70E).
警告：感電事故防止のため、取付けまたは修理の際は電源から取り外してく
ださい。適切なケース内に取付けてください。また、汚染物質がないことを
NFPA70E
確認してください。（
警告：为了防止触电，在安装或维修之前必须先切断电源。安装在合适的设备
箱内。防止接触污染 。符合NFPA70E要求）
物
DIR 1000719R0905 Version 01
-
の要件に従ってください）
140G-G
140G-H
140G-I
140G-J
140G-K
140G-M
140G-N
A
x1
B
C
x1
D
x1
D
x1
E
Bul. 140G/140MG
LENGTH
M
x1
42.5 mm (1 .67") M 3
LENGTH
M
x1
50.5 mm (1 .99") M 3
LENGTH
M
x2
60 mm (2.36") M 4
LENGTH
M
x2
40 mm (1 .57")
M 4
LENGTH
M
x1
40 mm (1 .57")
M 4
LENGTH
M
x1
50 mm (1 .97")
M 4
Publicité
Manuels Connexes pour Rockwell Automation Allen-Bradley 140G-G-OSB
Sommaire des Matières pour Rockwell Automation Allen-Bradley 140G-G-OSB
- Page 1 Bul. 140G/140MG DIR 1000719R0905 Version 01 - 140G-G-OSB, 140G-K-OSB, 140G-M-OSB, 140G-N-OSB Variable depth operating mechanism-support bracket for 140G-G,-K,-M,-N Supporto asta maniglia rotante rinviata Installation - Installazione - Instalación Instalação - WARNING: To prevent electrical shock, disconnect from power source before installing or servicing.
- Page 2 140G-G, 140G-I 140G-G, 140G-I 140G-H, 140G-J 140G-H, 140G-J 9.7 lb-in 1.1 Nm 140G-I only 140G-G, H, J only 140G-K 140G-K 9.7 lb-in 1.1 Nm DIR 1000719R0905 Version 01...
- Page 3 Allen-Bradley, Rockwell Software, and Rockwell Automation are trademarks of Rockwell Automation, Inc. Trademarks not belonging to Rockwell Automation are property of their respective companies. Rockwell Automation maintains current product environmental compliance information on its website at http://www.rockwellautomation.com/rockwellautomation/about-us/ sustainability-ethics/product-environmental-compliance.page Publication 140G-IN124B-MU-P - September 2015 DIR 1000719R0905 Version 01 - B0301 Copyright ©...