NVT Phybridge FLEX24-10G Guide D'installation Rapide

Quick Install Guide - FL E X2 4 -1 0 G
The FLEX24-10G Layer 3 managed switch delivers Gigabit Ethernet and PoE++
(50 watts per port) over multiple pairs of UTP cable with six times the reach of
traditional switches. FLEX was designed to make the migration to IP quick, easy
and cost effective by leveraging an existing 1, 2 or 4-pair UTP infrastructure.
Removable
Management (MGMT)
Power Supply
Status LEDs
Installation Details
System Grounding: See Page 5
Location and Regional Specifications:
The FLEX24-10G can be installed in any indoor location in all countries except Finland,
Norway and Sweden, where, in these 3 Nordic countries, it must be installed in a
restricted access location.
FLEX24-10G kan installeras på valfri plats inomhus i samtliga länder utom Finland,
Norge och Sverige; i dessa nordiska länder måste den installeras på en plats med
begränsad åtkomst.
Space Requirements:
1. Select a standard 19" equipment rack or, for a standalone installation, a flat, stable surface capable of supporting the size and weight of the FLEX24-10G, its
installable components and cabling.
2. Ensure that you have enough rack space for all equipment. Shelves and rear supporting brackets are not mandatory.
Location Requirements:
Power - The FLEX24-10G switch must be placed within 6 feet of an available power source. Do not use an extension cord to connect the equipment to a power outlet.
Ventilation - To ensure proper ventilation of the FLEX24-10G, leave at least 2 inches of unobstructed space on all sides of the unit. If the fans are blocked, the unit could
overheat.
Downlink – The adapters should be installed a minimum of 6 feet away from the FLEX24-10G switch.
Installation procedures will be trouble free if you ensure that the following items are available before you begin:
• The FLEX24-10G switch, all cables and accessories you received in the FLEX package.
• SFP/SFP+ transceiver modules for the 10G uplink ports (user-supplied).
• Fiber or UTP cable (user-supplied) for the SFP/SFP+ modules.
• UTP cable for the downlink ports (user-supplied).
• Serial console cable for the CONSOLE port, provided as an accessory in the product package.
• Standard CAT5e copper LAN cable for the MGMT port (optional). Only needed if out-of-band management is required (user supplied).
• Protective ground cable (user supplied).
Hardware Topology & Installation Overview
1. Remove the FLEX24-10G switch and all accompanying accessories.
2. Install the rackmount brackets for rack mounting. Unit fits in standard 19"
racks.
3. Install the protective grounding conductor (please refer to the System
Grounding section of this guide).
4. Remove all legacy devices from the cabling. Note: It is extremely important that
non-IP devices are not connected when you power on the FLEX24-10G.
5. Connect the infrastructure cable to the RJ45 on the FLEX24-10G switch.
FLEX24-10G
The Most Robust PoE Capabilities on the Market
Four switches can be stacked together for power sharing and power
redundancy. The FLEX24-10G switch comes standard with PowerWISE
technology.
888.901.3633 | +44 (0) 208 977 6614 | www.nvtphybridge.com
24 RJ45 Connectors With
& Console Port
Link/Activity LEDs
1 3 5 7 9
2 4 6 8 10
Reset
PoE over Multi-Pair UTP up to 2,000ft (610m)
IP Endpoint
11 13 15 17 19 21 23
12 14 16 18 20 22 24
2 SFP+ Ports
FLEX24-10G kan installeres overalt indendørs undtagen i Finland, Norge og Sverige,
hvor i disse tre nordiske lande den skal installeres på et sted med begrænset adgang.
FLEX24-10G kan installeres innendørs i alle land unntatt Finland, Norge og Sverge. I
disse tre nordiske landene må den installeres på et sted med begrenset tilgang.
6. Connect a downlink or uplink port to the network switch.
7. For power share, daisy chain FLEX24-10G switches using DC cables (see below).
8. Power up the FLEX24-10G.
9. For troubleshooting, please refer to the Hardware Installation Guide located at
www.nvtphybridge.com.
10. To revert back to factory defaults, hold the reset button for 50 seconds or until
the fault (!) LED on the power supply stops flashing red. Alternatively, factory
reset can be observed by connecting the console cable; command line of
switch will confirm that factory reset has occurred during the boot process.
Functions like a normal PoE+ switch for distances up to 328ft (100m).
No adapter required.
FLEX24-10G Package Includes:
1 x FLEX24-10G Unit
1 x Rackmount Bracket Kit
1 x Console Cable
1 x Power Cable
1 x Quick Install Guide
FLEX-Link
Local Power
Option
FLEX4
Local Power FLEX4
Option
Copyright 2020 NVT Phybridge | 445-0030 REV. B | Page 1
FLEX-C
IP Endpoint
IP Endpoint
FLEX-Link
Long Reach PoE over UTP
IP Endpoint
IP Endpoint
Long Reach PoE over UTP
IP Endpoint
IP Endpoint