Satco NUVO Sullivan Instructions D'installation

INSTALLATION AND SAFETY INSTRUCTIONS
FOR YOUR SAFETY
WARNING: BE SURE THE ELECTRICITY TO THE WIRES
YOU ARE WORKING ON IS SHUT OFF; EITHER THE FUSE IS
REMOVED OR THE CIRCUIT BREAKER IS SHUT OFF.
GENERAL
You don't need special tools to install this fixture. Be sure to follow
the steps in the order given. Under no circumstances should a
fixture be hung on house electrical wires, nor should a swag type
fixture be installed on a ceiling which contains a radiant type heating
system. Read instructions carefully. If you are unclear as to how to
proceed, consult a qualified electrician.
NOTE: Proper wiring is essential for the safe operation of this fixture.
FIXTURE ASSEMBLY
Carefully remove the fixture from the carton and check that all parts
are included as shown in figure. Be careful not to misplace any of
the screws or parts, which are needed to install this fixture.
INSTALLATION
IMPORTANT: Do not attach fixture directly to outlet box.
STEP 1: Thread the 2 mounting screws (B) into the mounting plate
(C) spaced the same distance apart as the holes in the fixture back
plate. (Adjust the length of the screws if necessary.)
STEP 2: Attach the mounting plate (C) to the outlet box (not
supplied) with mounting screws (D). Ground Wire must face out.
GROUNDING INSTRUCTIONS
STEP 1: Insert the green grounding screw into the hole with two
raised dimples on the mounting bar. Wrap the ground wire from the
fixture (if supplied) around the green grounding screw, then connect
it to ground wire from the outlet box (if not fixed on the outlet box)
using a wire connector (not supplied). If ground wire from the fixture
is not supplied, wrap the ground wire (if not fixed on the outlet box)
from the outlet box around the green grounding screw and tighten it.
NEVER CONNECT GROUND WIRE TO BLACK OR WHITE
POWER SUPPLY WIRES.
STEP 2: Take note of the color of the wire(s) on your fixture. Identify
which group your fixture wire(s) falls into and connect the wires
according to the directions below:
GROUP A:
Connect to Black House Wire
BLACK
* PARALLEL WIRE (round & smooth)
WHITE OR GREY WITH TRACER
BROWN, GOLD OR BLACK
WITHOUT TRACER
NOTE: When parallel wire (SPT-I & SPT-2) is used, the tracer wire is
square shaped or ridged and the less tracer wire is round in shape
or smooth (seen best when viewed from wire end.)
STEP 3: Take your fixture wire(s) from group A and place evenly
against the black wire from the outlet box. Do NOT twist wires
together before using wire connectors.
STEP 4: Fit a wire connector over the wires and screw the
connector clockwise until you feel firmness.
GROUP B:
Connect to White House Wire
WHITE
* PARALLEL WIRE (square & ridged)
WHITE OR GREY WITHOUT TRACER
BROWN, GOLD OR BLACK
WITH TRACER
FIGURE
Line art shown may not exactly match the fixture enclosed. However, the installations
do apply to this fixture.
La ilustración puede no concordar exactamente con la pieza enviada. Sin embargo,
las instalaciones sí aplican para esta pieza.
Les images peuvent ne pas correspondre exactement au luminaire de la boîte.
Par contre, les directives d'installation s'appliquent au luminaire.
STEP 5: Try gently to pull the connector off the wires. If you can pull
the connector off, carefully re-do steps 3 and 4 as above, and check
again for a firm connection.
STEP 6: Connect the fixture wire from group B to the white wire
from the outlet box in the same manner. Make sure no bare wires
can be seen outside wire connectors.
FINAL ASSEMBLY
STEP 1: Align the fixture back plate (E) to mounting plate (C) and
secure with washer (G) and screws (F).
STEP 2: Install Bulb (1) A19 100W MAX/Medium base (not included).
STEP 3: To prevent moisture from entering the outlet box and
causing a short, use clear caulking (i.e. Indoor/Outdoor Silicone
Sealant). Outline the outside of fixture back plate where it meets the
wall leaving a space at bottom to allow moisture a way to escape.
CLEANING
To clean, wipe fixture with a soft cloth. Clean glass with a mild soap.
Do not use abrasive materials such as scouring pads or powders,
steel wool or abrasive paper.
ORDERING PARTS
Keep this sheet for future reference, and in case you need to order
replacement parts. Be sure to use exact wording from illustration
when ordering parts.
ITEM NO: 60-7375, 60-7376
ARTÍCULO Nº: 60-7375, 60-7376
ARTICLE N°: 60-7375, 60-7376