Energy Power Bar Elite CS-30 Manuel Du Propriétaire page 4

ConnECtIon
1. Connecting the soundbar to your tV: The soundbar part of your Energy Power Bar
Elite system is what needs to be connected to your TV, Cable Box or Satellite Re-
ceiver. If you have other devices connected to your TV, such as a DVD /BluRay player,
gaming system, etc., connect the soundbar to the TV so that you can listen to all
those and your TV through the soundbar. If there are no other devices connected to
your TV other than a cable or satellite box and you receive all of your television pro-
grams from that box, you can connect the soundbar to either that box or your TV. There
are three different ways to connect the soundbar to your TV, Satellite or Cable box.
a. Digital optical Cable
Since most High Definition TV's, Satellite and Cable boxes have an DIGITAL OPTICAL AU-
DIO OUTPUT, we have included that cable. Simply connect one end of that included cable
into the corresponding output of your TV, Satellite or Cable box and connect the other end
of the cable into the DIGITAL OPTICAL INPUT on the back panel of the soundbar.
tV Connection Panel
B. rCa Cable
If you do not have an optical digital output, you can use analog left and right audio
outputs on your device and connect them to the analog left and right inputs on the
soundbar with the supplied cable.
tV Connection Panel
SUBWOOFER
VOLUME
MIN MAX
POWER
ON OFF
C. 3.5mm output (headphone Jack)
A third choice would be to connect from a headphone output on your device to the
analog left and right inputs on the soundbar (cable NOT supplied).
once you have made any of the above audio cable connections, connect the
supplied soundbar power supply into the "DC Input" on the back of the soundbar
and turn the main Power Switch on the back of the soundbar on.
OFF ON
Soundbar Connection Panel
1 SOURCE 2
DC IN
R
24V – 2.5A
65W
L
Digital optical Cable
(Supplied)
1 SOURCE 2
DC IN
L
24V – 2.7A
3.5mm to male rCa
65W
R
Cable
(Not Supplied)
male rCa to male
rCa Cable
(Supplied)
1 SOURCE 2
DC IN
R
POWER
24V – 2.5A
65W
L OFF
Soundbar Connection Panel
AC~100-240V
50/60Hz
1 SOURCE 2
90W DC IN
L
24V – 2.7A
65W
R
Soundbar Connection Panel
1 SOURCE 2
DC IN
R
POWER
24V – 2.5A
65W
OFF
L
Power Supply
and aC Cord
2. Connecting the subwoofer to the soundbar: Once you have placed the sub-
woofer in the room, take the supplied subwoofer power cord, plug one end into
the subwoofer where it is labeled "AC In" and plug the other end into an active
electrical socket. Turn the Main Power Switch on the back of the subwoofer on. On
the soundbar, make sure the left status light is either solid green or orange (press
SOURCE button once if light is steady red). The red light will turn on until it finds the
wireless signal coming from the soundbar. Once it finds that signal (approximately 15
seconds), the solid red light will change to solid blue, indicating the subwoofer is now
connected to the soundbar.
Subwoofer rear Connection Panel
POWER
OFF ON
ProGrammInG yoUr tV rEmotE to oPEratE thE SoUnDBar
The following 3 steps should be used to program each function of your TV or cable box
remote control buttons (SOURCE, MUTE, VOLUME UP, & VOLUME DOWN). IF THE SOUND-
BAR IS IN STANDBY MODE (solid red status light), push the <SOURCE> button on the
soundbar until the status light is solid GREEN.
Soundbar front
Control Panel
POWER
OFF ON
1. Place the unit in learning mode: With the status light showing solid GREEN, press and
hold down both the <SOURCE> and <MUTE> buttons on the front of the soundbar at
the same time (approximately 3 seconds) until the status light flashes ORANGE.
2. Select the function to learn: Press the <MUTE> button once on the soundbar (the
ON
status light changes to solid ORANGE). (Substitute the SOURCE, VOLUME UP &
VOLUME DOWN in place of <MUTE> when programming the other buttons during
this step)
3. Learn the function: Hold your remote control within one foot and pointed at the
POWER
front of the soundbar. Slowly press the <MUTE> button on your remote control four
OFF ON
times. On the first three presses, the status indicator light will flicker ORANGE with
each press. If the unit has successfully learned the function, on the fourth press of
the button, the light will flash GREEN several times and then turn to solid GREEN.
(Remember to use the SOURCE, VOLUME UP & VOLUME DOWN in place of <MUTE>
when programming the other buttons during this step)
To program the remaining functions, simply repeat all steps, substituting <MUTE> with
the new function and button presses (SOURCE, VOLUME UP, and VOLUME DOWN) on steps
TWO and THREE.
ON
SUBWOOFER
VOLUME
MIN MAX
POWER
AC~100-240V
ON OFF
50/60Hz
90W
1 SOURCE 2
DC IN
R
24V – 2.5A
65W
L OFF
StatUS LIGhtS
VoLUmE UP
VoLUmE DoWn
Status Light
aC Power Cord
POWER
ON
SoUrCE
mUtE