Ez Setup; Ch Setting - Sharp 13VT-CR10 Mode D'emploi

Watching A TV Program (Continued)
L CH SETTING
If EZ SETUP does not memorize all the channels in your
region, follow the instructions below to manually memorize
the channel.
1 Selecting the TV Signal mode.
(1) Select "CH SETTING" in
the MENU screen by
pressing + or – button,
then press the SET button.
(2) Select "AIR/CABLE" from
the CH SETTING screen
by pressing + or – button,
then press the SET button.
(3) Press the + or – button on
the Remote Control to
select the TV signal mode,
then press the SET button.
VHF/UHF antenna
Cable TV
2 Auto-programming broadcast TV channels into memory.
(1) Select "CH SEARCH"
from the CH SETTING
screen by pressing + or –
button, then press the
SET button.
(2) Press the SET button. The
tuner will automatically
cycle through available
channels in your area and
preset them into the
memory. If all available
channels are of reasonable
signal strength and you
prefer not to add or erase
any channels from memory,
presetting is completed.
Note:
• Receivable channels of your TV set are:
AIR channels —
VHF; 2 through 13,
UHF; 14 through 69.
CABLE channels —
1 (HRC and IRC mode only)
2 through 125 (STD, HRC, and IRC)
08-11 13VT-CR10[E].pm65e
Downloaded from: http://www.usersmanualguide.com/
M E N U
T I M E R
V I D E O A D J U S T
C L O S E D C A P T I O N
F U N C T I O N
C L O C K
L A N G U A G E
C H S E T T I N G
S E L E C T + / — : S E T
P R E V I O U S R E T U R N : Q U I T
C H S E T T I N G
E Z S E T U P
A I R / C A B L E
C H S E A R C H
C H M E M O R Y
S E L E C T + / — : S E T
P R E V I O U S R E T U R N : Q U I T
A I R / C A B L E
A I R
C A B L E S T D
C A B L E H R C
C A B L E I R C
AIR
CABLE STD
S E L E C T + / — : S E T
CABLE HRC
P R E V I O U S R E T U R N : Q U I T
CABLE IRC
(TV signal mode)
C H S E T T I N G
E Z S E T U P
A I R / C A B L E
C H S E A R C H
C H M E M O R Y
S E L E C T + / — : S E T
P R E V I O U S R E T U R N : Q U I T
C H S E A R C H
A I R 2
S T A R T
P R E V I O U S R E T U R N : Q U I T
11
3 Adding weak or additional channels from TV memory.
(1) Select "CH MEMORY"
from the CH SETTING
screen by pressing + or –
button, then press the
SET button.
(2) Use either the CH UP/DOWN
(8/9) buttons or the CHA-
NNEL SELECT buttons (0~9,
100) to select the desired
channel. The selected cha-
S E T
nnel number will appear on
M E N U
the screen.
• If any channel is stored in the memory, the "ADD" is
displayed.
• If any channel is not stored in the memory, the "ERASE" is
displayed.
(3) Use the + or – to select
"ADD"; confirm that the
S E T
"ADD" is displayed. If
M E N U
additional channels are to
be preset, repeat step (2).
(4) Press the SET or MENU
key to exit CH MEMORY.
Use the CH UP/DOWN
S E T
M E N U
(8/9) buttons to assure
channel presetting is
correct.
4 Erasing unwanted channels from TV memory.
(1) Select "CH MEMORY"
from the CH SETTING
screen.
(2) Select the channel to be
erased.
(3) Use the + or – to select
S E T
M E N U
"ERASE"; confirm that the
"ERASE" is displayed. If
additional channels are to
be erased, repeat step (2).
(4) Press the SET or MENU
key to exit CH MEMORY.
Use the CH UP/DOWN
(8/9) buttons to assure
S T A R T S E T
channel(s) are erased.
M E N U
C H M E M O R Y
A I R 5 4
A D D
S T A R T
S E L E C T + / — : S E T
P R E V I O U S R E T U R N : Q U I T
C H M E M O R Y
A I R 5 4
A D D
S T A R T
S E L E C T + / — : S E T
P R E V I O U S R E T U R N : Q U I T
C H M E M O R Y
A I R 5 4
E R A S E
S T A R T
S E L E C T + / — : S E T
P R E V I O U S R E T U R N : Q U I T
15/5/01, 7:24 pm
S E T
M E N U
S E T
M E N U
S E T
M E N U
11