Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
Changing the Settings on the LCD panel
1.
Mode
With the Crease die inserted, crease function can be turned
ON/OFF. REG.ACCURACY can be turned ON/OFF and can
improve the position and reliability of the crease. However, some
decrease in system productivity may occur in this mode even if
the crease die is not inserted.
2.
Backgage Depth Setting
Backgage is the distance of the punched hole(s) from the trail
edge of the sheet. This distance can be adjusted by entering the
Settings section (press Up or Down from the Home screen, and
press OK for Settings).
Pressing Up arrow will increase the Depth of Backgage, and
Pressing Down arrow will decrease the Depth of Backgage.
"-"ON THE LCD
DECREASES
BACKGAGE
DEPTH
When a crease die is inserted, the Backgage Depth options are:
1 Crease Mid
CR EASE LIN E
"+" ON T H E LCD
MOVES THE
CR EASE LINE IN
THIS DIRE CTION
Multi Function Professional Puncher – A1
BACKGAGE
"+"ON THE LCD
INCREASES
BACKGAGE
DEPTH
"-" ON THE LCD
MO VES T HE
CR EASE LI NE IN
THIS DIR E C TION
PAPE R FLOW DIR EC TION
3.
Skew Offsets (Only if Crease die is inserted)
The skew offsets can be adjusted to improve the angle of the
crease in the media.
i)
Print a 10 sheet job in
crease mode.
ii)
Measure L8 and L7 on
each sheet.
iii)
Calculate L8-L7 and divide
the average of (L8-L7) by
2. The number is "X".
iv)
Based on "X" and paper
size on the table below, search for input number "S" to
change either BG DP L REAR or BG DP XL REAR.
v)
If L8>L7, skew offset BG DP L/ XL REAR is negative "S".
vi)
If L8<L7, skew offset BG DP L/ XL REAR is positive "S".
vii) After inputting "S", print 1-sheet by crease mode.
viii) After measuring L8, calculate the difference between L8 and
original paper size mid position. Input this number into
"1Crease Mid", in the backgage menu to correct the crease
position.
BG DP L REAR
A4R
LTRR/LGL
LDR
210
216
X
0.025
1
1
0.05
1
1
0.075
2
2
0.1
3
3
0.125
3
3
0.15
4
4
0.175
5
4
0.2
5
5
0.225
6
6
0.25
7
6
0.275
7
7
0.3
8
8
0.325
8
8
0.35
9
9
0.375
10
10
0.4
10
10
0.425
11
11
0.45
12
11
0.475
12
12
0.5
13
13
0.525
14
13
0.55
14
14
0.575
15
15
0.6
16
15
0.625
16
16
0.65
17
17
0.675
18
17
0.7
18
18
0.725
19
18
0.75
20
19
0.775
20
20
0.8
20
0.825
0.85
0.875
0.9
0.925
0.95
0.975
1
1.025
1.05
1.075
1.1
1.125
1.15
1.175
1.2
1.225
Skew Offset Table
BG DP XL REAR
A3
12x18
SRA3
279
297
304.8
320
S
0
0
0
0
1
1
1
1
1
1
1
1
2
2
2
2
2
2
2
2
3
3
3
3
3
3
3
3
4
4
4
3
4
4
4
4
5
5
5
4
5
5
5
5
6
6
5
5
6
6
6
6
7
6
6
6
7
7
7
6
8
7
7
7
8
8
8
7
9
8
8
8
9
9
9
8
10
9
9
9
10
10
9
9
11
10
10
9
11
11
10
10
12
11
11
10
12
12
11
11
13
12
12
11
13
12
12
12
14
13
13
12
14
13
13
12
15
14
14
13
15
14
14
13
16
15
14
14
16
15
15
14
17
16
15
15
17
16
16
15
18
17
16
15
18
17
17
16
19
18
17
16
19
18
18
17
20
18
18
17
20
19
18
18
19
19
18
20
19
18
20
20
19
20
19
20
20
EN
13X19
330.2
0
1
1
2
2
2
3
3
4
4
5
5
5
6
6
7
7
7
8
8
9
9
10
10
10
11
11
12
12
12
13
13
14
14
15
15
15
16
16
17
17
17
18
18
19
19
20
20
20
8
Publicité
Table des Matières
