Publicité
Les langues disponibles
Les langues disponibles
Liens rapides
Trunk Pan
Hitch Shown In Proper Position
Equipment Required: Sealant
Fastener Kit: F24726
Wrenches: 9/16, 3/4
Drill Bits: 1/2"
Fasteners typical both sides.
1
Qty. (4)
Carriage Bolt 1/2-13 X 1.75
2
Qty. (4)
Block
3
Qty. (4)
Lock Washer 1/2
4
Qty. (4)
Hex Nut 1/2-13
1.
REMOVE SPARE TIRE FROM INSIDE TRUNK
2.
Raise hitch into position centered on vehicle, sliding hitch forward on vehicle until receiver tube contacts tow hook.
3.
Install 3/8" U-Bolt through tow hook and hitch bracket as shown above. Fasten with flat washers and nuts as shown. Make
sure flat washers Do Not Overlap.
4.
Using hitch as a template, drill 1/2" holes in vehicle trunk pan as shown. REMOVE SPARE TIRE BEFORE DRILLING.
5.
Install 1/2" fasteners as shown.
Note: Remove sound-deadening material as needed inside trunk to insure block sits flat on metal trunk surface.
6.
Seal all holes drilled into vehicle to prevent entry of exhaust fumes into trunk.
7.
Return spare tire to vehicle trunk.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to
prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working
beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5
and SAE J684.
z
2002, 2006 Cequent Towing Products
Installation Instructions
Fascia
Drawbar Kit:
Drawbar must be used in the
RISE position only.
1
2
Trunk Pan
Tighten all 3/8-16 GR2 fasteners with torque wrench to 20 Lb.-Ft. (27N*M)
Tighten all 1/2-13 GR5 fasteners with torque wrench to 75 Lb.-Ft. (102 N*M)
Hyundai Tiburon
3592
5
3
4
5
Qty. (1)
6
Qty. (2)
7
Qty. (2)
Sheet 1 of 3
Do Not Exceed Lower of Towing Vehicle
Manufacturer's Rating or
2000 LB (908 Kg) Max Gross Trailer Weight
200 LB (90.8 Kg) Max Tongue Weight
Wiring Access Location: PC3, PC4
REMOVE SPARE TIRE
BEFORE DRILLING
Tow Hook
6
7
U-Blot 3/8-16
Flat Washer 3/8
Lock Nut Hex 3/8-16
N24726
3-3-06
Part Numbers:
24726
77042
60825
Rev. A
Form: F205 Rev A 5-6-05
Publicité
Manuels Connexes pour Cequent Towing Products 24726
Sommaire des Matières pour Cequent Towing Products 24726
- Page 1 Do not cut access or attachment holes with a torch. This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684. 2002, 2006 Cequent Towing Products Sheet 1 of 3 N24726 3-3-06 Rev.
- Page 2 Ce produit est conforme aux normes V-5 et SAE J684 de la V.E.S.C. (État de New York) concernant les spécifications en matière de sécurité des systèmes d’attelage. 2002, 2006 Cequent Towing Products Feuille 2 de 3 N24726 3-3-06 Rev.
- Page 3 Observe las precauciones de seguridad al trabajar por debajo del vehículo y use protección visual. No corte los orificios de acceso o accesorios con soplete. Este producto cumple con las especificaciones y requisitos de seguridad para conectar dispositivos y sistemas de remolque del estado de Nueva York, V.E.S.C. Regulación V-5 y SAE J684 2002, 2006 Cequent Towing Products Hoja 3 de 3 N24726 3-3-06 Rev.