Cequent Towing Products 24775 Instructions D'installation

Optional Drawbar (Sold Seperately)
For MAZDA 6 ONLY 3594
Drawbar must be used in the RISE
Position only.
nner Bumper Structure
Trunk Pan/Spare
Tire Well
Hitch Shown In Proper Position
E Equipment Required: Pull Wire (Provided) i R i d P ll Wi (P
Fastener Kit: 24775F
Wrenches: 12mm, 13mm, 3/4
Drill Bits: ½"
Pull Wire
Fasteners Typical
Both Sides of Vehicle Both Sides of Vehicle
1
Qty. (2) Hex Bolt ½-13 x 1-1/2" Gr. 5
2
Qty. (2) Carriage Bolt ½-13 Gr. 5
3
Qty. (2) Block ¼ x 1 x 2
4
Qty. (2) Block 3/16 x 1-1/2 x 2
1. Lower muffler by removing (3) rubber isolator hangers, (2) located near the end of the muffler and the remaining hanger forward
of the rear axle. Remove (2) rubber plugs from the trunk pan (if present).
2. Remove 8mm bolt, located on the inside of the frame rail on the bulkhead, both sides of vehicle. Discard bolts.
3. Slide hitch above tailpipes with inner bumper straps sliding under fascia (Note: Care must be taken when sliding inner bumper
straps under fascia to prevent scratching). Install 8mm bolts (Item
4. If vehicle bumper has a slots which line up with hole in inner bumper strap, proceed to step 5. If no slots exist, use hitch inner
bumper straps as a template to drill (2) ½" holes in vehicle bumper.
5. Install carriage bolt and block (Item g
slot/drilled hole in bumper and hitch. Install conical toothed washer and nut.
6. Install hex bolt and block (Item
as a template to drill (2) ½" holes in trunk pan. Install fasteners as shown.
7. Seal holes in trunk pan to prevent intrusion of exhaust fumes or water.
8. Reinstall muffler, (3) places.
9. 9 Reinstall spare tire in trunk Reinstall spare tire in trunk.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to
prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working
beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5
and SAE J684.
z
2006, 2007 Cequent Towing Products
Installation Instructions
Mazda 6 - Sedan & 5-Door (does not fit wagons)
Ford Fusion, Mercury Milan, Lincoln Zephyr,
Fascia
Drawbar Kit:
3592
Drawbar must be used in the
Rise position only.
id d)
Bumper
Inner Bumper
Strap
3
( ) ) thru inner bumper structure with pull wire, carefully pulling fastener thru existing
Tighten all ½-13 GR5 fasteners to 75 lb.-ft. (102 N*M)
Tighten all 8mm fasteners to 25 lb.-ft. (34 N*M)
4
) thru holes in trunk pan, if present. If holes are not present, remove spare tire and use hitch
Tighten all ½-13 GR5 fasteners to 75 lb.-ft. (102 N*M)
Lincoln MKZ
Inner Bumper Structure
5
Qty. (4)
6
Qty. (4)
7
Qty. (2)
7
) loosely thru upright brackets.
p p
Sheet 1 of 3
Do Not Exceed Lower of Towing Vehicle
Manufacturer's Rating or
2000 LB (908 Kg) Max Gross Trailer Weight
200 LB (90.8Kg) Max Tongue Weight
Wiring Access Location: PC3, PC4
Note: Remove Spare Tire
Before Drilling
Conical Toothed Washer 1/2"
Nut ½-13
Bolt M8 x 1.25 x 35mm CL9.8
y p g
24775N 10-22-07
Part Numbers:
24775, 77152
60846, 24859UH
Trunk Pan – Spare
Tire Well
Existing Holes or
Holes to be Drilled
p
g
Rev. D