Publicité
Les langues disponibles
Les langues disponibles
1 - How to get started.
Start by locating the footings and check that the
necessary space, including the safety zone, is available.
Safety zone plan is present in the Product Guide. (1)
2 - Measurement
Place two tape measures in a cross in the area where
the system is to be installed. (2)
Use the plan drawing in the Product Guide (3) to locate
the point where the two tape measures have to cross.
In the drawing the point is indicated where line X and
line Y cross. Make sure that the two tape measures are
perpendicular.
Measure out the center points indicated for the
foundations for the entire system. Mark these points with
pegs, screwdrivers or similar. (4) Then check that the
safety zone around the entire system has been complied
with.
The safety zone is indicated by a dotted line around the
system on the plan drawing.
The plan drawing shows a hatched area with a number
(1, 2, 3, 4, 5, 6, etc.) at each of the marked center points.
The hatched area indicates the size of the foundation
plate.
Each hatched area is numbered, and the number refers
to a drawing showing the size and depth of the hole and
the amount of concrete to be used.
The drawings are on the last page in the Product Guide
If mechanical digging is used, it is a good idea to
combine several foundation holes in a single excavation.
Make sure that the ends of line X and line Y have been
marked before removing the tape measures to allow
digging. It is important to be able to check and make
sure that the system is positioned correctly throughout
installation.
3 - Footing holes for in-ground installation
Dig holes for posts, see digging plan (5),
indicating which activities require concrete.
Please note. Do not ill the holes until assembly
is complete and the entire structure is plumb
and level.
Copyright©KOMPAN A/S
1
2
3
5
60cm(24") - CP120300/CP121300 85cm(34") - CP120400/CP121400
1
min.20 cm - 8"
2
min.20 cm - 8"
3a
50 cm - 20"
60cm(24") - CP120300/CP121300
4
min.20 cm - 8"
4
3/14
5
a
XX
XX
R
85 cm
34"
60 cm
60 cm
24"
XX
XX
24"
F
6
a
b
a
b
R
R
R
90 cm
35,4"
60 cm
60 cm
24"
F
24"
F
F
3b
7
20 cm - 8"
60 cm - 24"
20 cm - 8"
50 cm - 20"
25 cm - 10"
R
R
55 cm
85 cm
22"
34"
F
F
85cm(34") - CP120400/CP121400
8
50 cm - 20"
40 cm
70 cm - 28"
15,8"
10 cm
R
4"
85 cm
34"
60 cm
F
24"
50 cm
45 cm
20"
17,7"
60cm (22") - R = F
85cm(34") - R = F
Concrete - Beton - Béton - Hormigón - Cemento - Betong -
- Betonointi
Concrete - Beton - Béton - Hormigón - Cemento - Betong -
- Betonointi
INCH
1
CM
1
2
CPxxxx
b
R
90 cm
35,4"
F
R
90 cm
35,4"
F
R
85 cm
33"
F
R: Resilient surfacing - Fallschutzbelag
Revêtement amortissant - Recubrimiento
amortiguador - Materiale ammortizzanto
Veiligheidsondergrond - Fallunderlag
Faldunderlag -
Turva-alusta
80 cm
32"
F: Foundation - Fundament - Fondement
Fondazione - Fundamento - Fonden - Stiftelsen
Perustus - Stichting -
Copyright©KOMPAN A/S
Publicité
