The Blender Functions; Cleaning & Maintenance - Inventum NB230RS Mode D'emploi

5

the blender functions

BLEND
1. Place the blender on a flat, clean and dry surface.
2. Cut the vegetables, for example carrots, into large pieces. Fill the jug with the pieces of carrot. In order to allow the blender to make
a good smoothie, always add a liquid with the vegetables. A good ratio is 2 : 3. Two parts carrot on three parts water.
Note: do not overfill! To avoid spilling, do not add ingredients past the maximum - MAX - fill line.
3. Place the blade assembly onto the jug and twist it on tightly until you have a good seal.
4. Turn the jug upside down and place it onto the base, aligning the tabs on the jug with the base. Push the jug down and turn it
clockwise, until you feel it click into place.
5. Plug the appliance in and press the start stop button to activate the blender.
6. The blender will stop automatically after 60 seconds or press the start stop button again to stop the blender.
Note: Do not activate the blender constantly, this can cause engine problems. Do not use the blender for more then 1 minute
continuously, wait 10 minutes before you operate it again.
CRUSH ICE
1. Place the blender on a flat, clean and dry surface.
2. Put the ice cubes (max. 10 pieces) in a large jug (700 ml).
Note: do not overfill! To avoid spilling, do not add ingredients past the maximum - MAX - fill line.
3. Place the blade assembly onto the jug and twist it on tightly until you have a good seal.
4. Turn the jug upside down and place it onto the base, aligning the tabs on the jug with the base. Push the jug down and turn it
clockwise, until you feel it click into place.
5. Plug the appliance in and press the start stop button to activate the blender or use the pulse button.
6. It takes about 30 seconds to crush the ice.
Note: Do not activate the blender constantly, this can cause engine problems. Do not use the blender for more then 1 minute
continuously, wait 10 minutes before you operate it again.
GRIND
1. Place the blender on a flat, clean and dry surface.
2. Measure 100 grams of roasted coffee beans and put it into a jug.
Note: the maximum capacity to grind is 100 grams.
3. Place the blade assembly onto the jug and twist it on tightly until you have a good seal.
4. Turn the jug upside down and place it onto the base, aligning the tabs on the jug with the base. Push the jug down and turn it
clockwise, until you feel it click into place.
5. Plug the appliance in and press the start stop button to activate the blender or use the pulse button.
6. It takes about 30 seconds to grind the coffee beans.
Note: Do not activate the blender constantly, this can cause engine problems. Do not use the blender for more then 1 minute
continuously, wait 10 minutes before you operate it again.
6
cleaning & maintenance
Always unplug the cord from the socket before cleaning the appliance.
• Rinse the jugs after every use under running water.
• Wipe the base with a damp cloth. Do not use any abrasive or strong detergents.
• Never place the appliance, the power cable or the plug in water or any other liquid.
• All the accessories - except the base - are dishwasher safe. The accessories - except the base - may also be cleaned with warm
soapy water.
• Attention: the blade assembly is extremely sharp. Clean the blade sets as a whole do not try to take them apart. Attention: do not
use any abrasive or strong detergents.
• Dry all the accessories thoroughly and reassemble them again. Note: do not store a jug with the lid completely closed to allow air to
circulate and prevent odors inside the jug.
The following accessories may be cleaned in a dishwasher: lid, jug (300 ml), 2 x jug (700 ml), blade assembly and lid with drinking
spout.
12
• English