MAT Industries ProForce 2000 XL Manuel De L'opérateur page 9

Table des Matières

Publicité

Les langues disponibles

Les langues disponibles

STORaGe
PUMP STORaGe
If you must store your pressure washer in a location where the
temperature is below 32°F, you can minimize the chance of damage
to your machine by utilizing the following procedure:
1.
Shut off water supply and relieve pressure in the spray gun
by depressing the trigger. Disconnect the garden hose
from the pressure washer, but leave the high-pressure hose
connected.
2.
Tip the unit on its side with the inlet connection pointing up.
3.
Insert a small funnel (to prevent spilling) into the inlet
and pour in approximately 1/4 cup of RV antifreeze.
4.
Disconnect spark plug wire.
5.
Without connecting garden hose pull the recoil several
times to circulate the antifreeze in the pump system.
Continue to add antifreeze and pull the recoil until the
antifreeze is expelled when the trigger is pulled.
6.
Turn the unit upright.
Prior to restarting, thaw out any possible ice from the
pressure washer hoses, spray gun and wand.
Another method of reducing risks of freeze damage is to drain
your pressure washer as follow:
1.
Stop the pressure washer and detach supply hose and high
pressure hose. Squeeze the trigger of the discharge gun to
drain all water from the wand and hose.
2.
Restart the pressure washer and let it run briefly (about 5
seconds) until water no longer discharges from the high
pressure outlet.
eNGINe STORaGe
When the pressure washer is not being operated or is being
stored more than one month, follow these instructions:
1.
Replenish engine oil to upper level.
2.
Drain gasoline from fuel tank, fuel line, fuel valve and
carburetor.
3.
Pour about one teaspoon of engine oil through the spark
plug hole, pull the recoil starter several times and replace
the plug. Then pull the starter slowly until you feel
increased pressure which indicates the piston is on its
compression stroke and leave it in that position. This
closes both the intake and exhaust valves to prevent the
inside of the cylinder from rusting.
4.
Cover the pressure washer and store in a clean, dry place
that is well ventilated away from open flame or sparks.
NOTe: We recommend always using a fuel stabilizer. a fuel
stabilizer will minimize the formulation of fuel gum deposits
during storage. The fuel stabilizer can be added to the gasoline
in the fuel tank, or into the gasoline in a storage container.
pro-forceproducts.com
LIMITeD WaRRaNTY
Warranty Coverage: MAT Industries, LLC (the Company)
warrants to the original retail customer in North America that it will
repair or replace, free of charge, any parts found by the Company or
its authorized service representative to be defective in material or
workmanship. This warranty covers the cost of replacement parts
and labor for defects in material or workmanship.
Not Covered:
·
Transportation charges for sending the product to the Company
or its authorized service representative for warranty service, or
for shipping repaired or replacement products back to the
customer; these charges must be borne by the customer.
·
Engine may be covered exclusively by a separate warranty from
the engine manufacturer as set forth in the engine Manual (if
included).
·
Damages caused by abuse or accident, and the effects of
corrosion, erosion and normal wear and tear.
·
Warranty is void if the customer fails to maintain and operate
the product as instructed and recommended by the Company in
the owner's manual.
·
Warranty applies only if the product is used solely for consumer
applications, and does not apply if the product is used for
commercial or business applications, or as rental equipment.
·
The Company will not pay for repairs or adjustments to the
product, or for any costs or labor, performed without the
Company's prior authorization.
Warranty Period: One (1) year from the date of purchase. For
warranty service, the customer must provide dated proof of purchase
and must notify the Company within the warranty period.
For warranty service: Call toll free 1-888-895-4549, or write to
MAT Industries, LLC, 6700 Wildlife Way, Long Grove, IL 60047.
EXCLUSIONS AND LIMITATIONS: THE COMPANY MAKES
NO OTHER WARRANTY OF ANY KIND, EXPRESS OR
IMPLIED. IMPLIED WARRANTIES, INCLUDING
WARRANTIES OF MERCHANTABILITY AND OF FITNESS FOR
A PARTICULAR PURPOSE, ARE HEREBY DISCLAIMED. THE
WARRANTY SERVICE DESCRIBED ABOVE IS THE
EXCLUSIVE REMEDY UNDER THIS WARRANTY; LIABILITY
FOR INCIDENTAL AND CONSEQUENTIAL DAMAGES IS
EXCLUDED TO THE EXTENT PERMITTED BY LAW.
This warranty gives you specific legal rights, and you may also have
other rights which vary from state to state. Some states do not allow
a disclaimer of implied warranties, or the exclusion or limitation of
incidental and consequential damages, so the above disclaimers and
exclusions may not apply to you.
English
9

Publicité

Table des Matières
loading

Produits Connexes pour MAT Industries ProForce 2000 XL

Table des Matières