TASSILI TANGO-3 Guide D'installation page 10

Before continuing, determine the type of water supply connection you have using
9a
the chart below and use the appropriate assembly parts to properly reconnect
the water supply.
TUYAU ÉVASÉ TUYAU JOINTÉ
EN MÉTAL / CUIVRE EN MÉTAL
LOCK NUT
CONE WASHER
COUPLING NUT
WATER SHUT-OFF
USE THE EXISTING COUPLING
THESE PARTS MUST BE USED
NUT AND WASHER.
AS ILLUSTRATED TO ENSURE
A WATERTIGHT CONNECTION.
THE USE OF AN EXISTING
COUPLING NUT MAY RESULT IN
WATER LEAKAGE. THE WATER
SUPPLY TUBE OR PIPE MUST
EXTEND AT LEAST ½ IN. INSIDE
THE THREADED SHANK OF THE
VALVE (DOES NOT APPLY TO
FLANGED TUBING).
CAUTION: DO NOT USE CONE WASHER WITH PLASTIC
SUPPLY LINE.
WARNING:
Do not use plumbers putty, solder paste, or any other sealant on the water supply connection to this tank. If the tank leaks after ma-
nually tightening, replace the supply tube. If the connection continues to leak with the new supply tube, replace the fill valve.
The warranty will be void if any type of sealant is used on the water supply connection.
ARM NIPPLE
TOP
CRITICAL
LEVEL MARK
( ˝C.L.˝) MUST
BE 1˝ ABOVE
OVERFLOW
PIPE
FLOAT
CUP
FILL VALVE
VALVA
BODY WATER LEVEL
ADJUSTMENT
ADJUSTABLE
HEIGHT
LOCK NUT
THREADED
CONE
SHANK
WASHER
PARTS FOR WATER CONNECTION
COUPLING NUT
(SEE STEP 9)
(HAND TIGHT ONLY)
TUYAU SPIRAL
EN MÉTAL
LOCK NUT
EXISTING WASHER
EXISTING COU-
PLING NUT
WATER SHUT-OFF
USE THE EXISTING SPIRAL
CONE WASHER. THE SPIRAL
CONE WASHER MAY NOT SEAL
COMPLETELY ON SPIRAL TYPE
SUPPLY LINE.
PUSH BUTTON
REFILL TUBE
SET
WATER
LEVEL
HERE
ADJUSTMENT
FULL FLUSH
ADJUSTMENT
BAYONET
RELEASE
ROD
SHANK
WASHER
Diagram 1
RACCORDEMENT
EN VINYLE / TRESSÉ
LOCK NUT LOCK NUT
EXISTING CONE COUPLING NUT
WASHER
COULING NUT
WATER SHUT-OFF WATER SHUT-OFF
WATERTIGHT CONE WASHERS
ARE ALREADY INCLUDED.
NO ADDITIONAL WASHERS
NEEDED.
CAUTION: Overtightening the LOCK NUT or COUPLING NUT
could result in breaking or potential leakage.
ADJUSTMENTS
a) Adjust water level. The water level should be adjusted to the
level indicated on the tank by adjusting the float cup.
See step 11 for water adjustment method.
b) Flush Valve Setting Adjustments:
NOTE: All other settings will result in either more or less water
and is not recommended.
FLUSH
VALVE
FLUSH VALVE SETTING
ADJUSTMENTS
PARTIAL
FLUSH
FULL FLUSH ADJUSTMENT
PARTIAL FLUSH
ADJUSTMENT
SILICONE
• To remove the flush valve, apply a slight downward pressure
SEAL
and twist until the flush valve disengages from the bayonet.
VALVE SEAT
• To reinstall the flush valve, reverse the procedure, making sure
the blue (partial flush button) aligns with the partial flush but-
ton with the dots on the tank cover.
- 4 -
9b
With the correct washers in place
(see step 9a), manually tighten the
COUPLING NUT a ¼ turn.
DO NOT OVERTIGHTEN.
WITHOUT LINER #
4349.216
4348.216
4339.216
2
2,5
WITH LINER
TANK #
4349.516
4348.516
4339.516
4
4,5