Chicco Next2Me Dream Guide D'assemblage page 15

To make installation easy, when fastening the buckles, always
keep the crib slightly away from the parents' bed.
6. At this point put the crib against the parents' bed and tighten
the noose pulling the straps (fig.23). Carry out this step first
on one side and then on the other, adjusting the straps until
the crib is in contact with the parents' mattress.
WARNING: Before use, always make sure that there is no space
between the parents' mattress and crib's side. Otherwise adjust
the straps pulling them until the required condition is restored.
Make sure that the side is always free to be lowered and raised
completely.
7. Fit the length of the straps in excess inside the pocket on the
bottom of the fabric lining.
8. Lock the crib's wheels.
If when fastening the crib to the parents' bed it is not possible to
fit the crib's feet under the parents' bed, the bed can be fastened
anyway by the following the instructions above and rotating the
articulated feet when putting the crib against the bed.
To turn the feet, pull the rotation release button "A4" and turn
the feet "A5" of the crib inward by hand (fig.24).
9. To close the side that can be lowered, just pull up by holding
it by the upper mobile structure "B2" (fig.25). Always make
sure that it is engaged correctly.
WARNING: Whenever the side is lowered, make sure that the
position compared to the parents' mattress has not changed
from that illustrated in the paragraphs above.
WARNING: Never use the rocking function when the crib is in
"Bedside sleeper configuration (fastened to the bed). "
WARNING: Use the product with beds and/or mattresses with
straight sides only. Do not use the product with round beds
and/or mattresses or water mattresses.
WARNING: When the product is used in "Bedside sleeper con-
figuration (fastened to the bed), " it must always be mounted on
the long side of the bed. DO NOT install the product at the head
or feet of the bed.
CARE AND MAINTENANCE
The crib and mattress have a resistant fabric lining that can be
removed completely and washed.
To remove the fabric, follow the instructions in the paragraph
"HOW TO REMOVE THE FABRIC COVER. "
WARNING: Covering or removing the fabric may take a few
minutes and must be carried out by an adult.
Regularly inspect the toy for signs of wear and any damage.
In the case of damage do not use and keep out of reach of
children.
When washing the fabrics pay close attention to the instruc-
tions on the label.
Do not use solvents, abrasive or overly aggressive products.
Wash by hand in cold water
Do not bleach
C
Do not tumble dry
Do not iron
Do not dry clean
Check that the fabric and the stitching are in good condition
after each wash.
WARNING: When covering or removing the cover, take care
when handling the fabric parts so as to avoid accidental tears
or damage.
DOING THE BED
It is possible to unfasten the crib from the parents' bed when
doing the bed. Just unfasten the grey buckles under the fabric
lining.
When fastening the crib again to the parents' bed, pull the
straps again to make sure that the crib is correctly and securely
fastened to the parents' bed. Make sure that all the steps illus-
trated above in "Bedside sleeper configuration (fastened to the
bed)" have been completed.
HOW TO REMOVE THE FABRIC COVER
1. Remove the mattress and unfasten the buttons in the lower
part of the fabric following the procedure illustrated in "AS-
SEMBLY OF THE CRIB" in opposite order.
2. Open the 3 zippers "E3" on the upper structure "B" and unfas-
ten the 4 buttons fastening the fabric to the upper structure.
3. Press the buttons on the fasteners of the feet, turn the upper
bar structure up and pull the upper structure out of the feet
(fig.26A-B)
4. Then remove the fabric lining.
DISASSEMBLING THE CRIB:
The crib can be disassembled completely to put it away in the
supplied bag. In order to complete the disassembly of the crib
after removing the fabric, remove the lower bar and the central
support structure by repeating the steps illustrated in "ASSEM-
BLY OF THE CRIB. "
ROCKING CONFIGURATION
To use rocking configuration:
1. Pull out the slides "A2" on the lower part of the feet of the
crib positioning the foot near the centre of the top of each
slide and, holding the upper edge of the crib with your hand,
pull the crib up while holding the crib down with your foot
(fig.27).
2. Repeat the same operation for both sides.
3. To deactivate rocking configuration, just press the button "A7"
at the centre of the slide on each side and then accompany
the crib down holding by the upper edge so that the slide
returns to closed position (fig.28). Always make sure that the
slide has returned to closed position.
WARNING: Always remember to deactivate rocking configu-
ration when using the product in "Bedside sleeper(fastened to
the bed)" or when the child is unattended.
WARNING: It is not possible to select different heights on the
two sides of the crib when in rocking configuration.
WARRANTY
The product is guaranteed against any conformity defect in
normal conditions of use as provided for by the instructions for
use. The warranty shall not therefore apply in the case of dam-
ages caused by improper use, wear or accidental events. For
the duration of warranty on conformity defects please refer to
the specific provisions of national laws applicable in the coun-
try of purchase, where provided.
15