Panasonic PV-20DF25-K Mode D'emploi page 43

• When appears on the screen while a button is being pressed, it means that the corresponding operation is prohibited by the unit
or the disc.
Selecting AUDIO OUTPUT
DVD-V
Select the digital output to be output from the optical digital audio
output connector of the unit.
1
Press ACTION in Stop mode to display MAIN MENU.
2
Press ▲▼◄► to select
"DVD."
3
Press SET to display DVD
MAIN MENU.
4
Press ▲▼ to select "AUDIO
OUTPUT."
5
Press SET to display AUDIO
OUTPUT screen.
6
Press ▲▼ to select an item.
7
Press SET repeatedly for
desired output.
LPCM (DVD)
OFF:
Linear PCM of less than 48 kHz/16 bit is output. When playing
DVDs recorded in linear PCM of over 48 kHz/20 bit, no digital
audio is output. (Factory preset)
PCM:
When playing DVDs recorded in linear PCM of 48 kHz/20 bit/24
bit or more, digital audio converted to 44.1 kHz/16 bit or 48
kHz/16 bit is output.
(Digital output of PCM audio is restricted to 48 kHz/16 bit or
below for copyright protection.)
Dolby Digital
Bitstream:
Dolby Digital bitstream (1ch-5.1ch) is output. (Factory preset)
PCM:
When you have connected an amplifier that doesn't have a built-
in Dolby Digital decoder.
dts selection
Bitstream:
dts bitstream is output. (Factory preset)
PCM:
When you have connected an amplifier that doesn't have a built-
in dts decoder.
All manuals and user guides at all-guides.com
DRC (Dynamic Range Compression)
OFF:
Normal audio range is selected. (Factory preset)
ON:
For dynamic sound even at low volume. This is useful for late-
night listening. [Dolby Digital DVDs only].
MAIN MENU
Type of amplifier to be
connected
DVD LOCK LANGUAGE
TV CLOCK CH
No amplifier is
SELECT: SET:SET
END :ACTION
connected
AV amplifier without
Dolby Digital/dts
D V D M A I N M E N U
decoder
D I S C L A N G U A G E S
A U D I O O U T P U T
S T I L L M O D E : A U T O
T V M O D E : 4 : 3 P a n & S c a n
AV amplifier including
S E L E C T : ▲ ▼ Dolby Digital decoder
S E T : S E T
E N D : A C T I O N
AV amplifier including
Dolby Digital/dts
decoder
A U D I O O U T P U T
L P C M ( D V D ) : O F F
D o l b y D i g i t a l : B i t s t r e a m
d t s : B i t s t r e a m
* When connecting an amplifier (with an optical digital input connector)
1
D R C : O F F
which does not contain the Dolby Digital or dts decoder, be sure to
S E L E C T : ▲ ▼ select "PCM." If "Bitstream" is selected, starting DVD play may cause
S E T : S E T
E N D : A C T I O N
such a high level of noise as to be harmful to your ears and damage
the speakers.
* 2 When a dts decoder is connected, please select "Bitstream" in "dts." If
"PCM" is selected, there will be stereo sound.
* 3 When a Dolby Digital decoder is connected, please select "Bitstream"
in "Dolby Digital." If "PCM" is selected, there will be stereo sound.
Note:
• Make settings according to amplifier connected to optical audio output
as shown in above table.
8
Press ACTION to redisplay DVD MAIN MENU and go
to step 4 to set up another item. Or, press ACTION
three times to exit.
Recommended setting
LPCM Dolby
dts
(DVD) Digital
PCM PCM* PCM*
1 1
PCM Bitstream* 3 PCM
PCM Bitstream* 3 Bitstream* 2
43