Preparing For Operation; Important - Enerco MR. HEATER MH50KT Mode D'emploi

1. Assemble the wheels onto the wheel support frame as
follows:
a. Install one of the cotter pins into the hole on one end of
axle.
b. Slide the large washer, then wheel onto the axle next to
the cotter pin.
c. Slide a small washer, spacer, small washer onto the axle
next to the wheel.
d. Slide the partially assembled axle through the wheel
support frame.
e. Slide the small washer, spacer, and small washer onto
the axle next to the wheel support.
f. Slide the wheel then large washer onto the axle and
hold in place with the remaining cotter pin.
g. Install the caps over the larger washers to finish the
wheel assembly.
2. Position the heater on the wheel support frame assembly
with the exit end over the wheels.
3. Use eight screws and nuts to attach the handles to the top of
the tank flange. The screws will go through the handles,
tank flange and wheel support frame. Install the nuts and
finger tight only until all nuts are installed.
4. Tighten all the nuts.
5. Attach cord caddies to handles using No. (14) & No. (5)
screws and nuts.

PREPARING FOR OPERATION

1. Check the heater for possible shipping damage. If any is
found, immediately notify the factory.
2. Follow all of the "Precautions".
3. Fill the fuel tank with clean kerosene. In extremely cold
weather, condensation may develop in the tank and it is
recommended that a tablespoon of de-icer be added for each
gallon (4 liters) of fuel in the tank. When filling the heater, use
at least 2 gallons (8 liters) of fuel. Be sure heater is level and
do not overfill. Use a funnel or can with a long fill spout.
IMPORTANT: Before filling fuel tank the first time or after
extended storage periods, drain the fuel tank of any moisture
or condensation.
4. Locate heater at a safe distance from combustible materials.
ModelS 50K & 75KT is not suitable for use on wood floors or
other combustible materials. When used, the heater should
rest on suitable insulating material at least 1 inch thick and
extending 3 ft. or more beyond the heater in all directions.
START
1. 50K: Plug the heater into a grounded 115V, 60 Hz, 1 Ø
outlet.
75KT, 125KT & 175KT: Turn thermostat to lowest
setting, make sure "On/Off" switch is "Off". Plug the
heater into a grounded 115V, 60 Hz, 1 Ø outlet. Turn
thermostat to highest setting. Start heater by push
toggle switch to "On" position (light signifies switch is
in "ON" position). Adjust thermostat to desired setting.
Heater will cycle on/off as heat is required.
Enerco Group, Inc. | Kerosene Forced Air Heater
All manuals and user guides at all-guides.com
STOP
1.
RESTART AFTER SAFETY SHUTDOWN (50K, 75KT, 125KT
1.
2. Press reset button.
4
For all models: In cold weather, starting may be
improved by holding a finger over the end of the
pressure adjusting screw until the heater starts. This unit
is equipped with a circuit breaker located near the power
cord. If the unit does not start, check to see that the
reset button is pressed in.
50K: Unplug heater from power source.
75KT, 125KT & 175KT: Push "On/Off" switch to "Off"
position. For extended shutdown, unplug heater from
power source.
& 175KT)
Wait 5 minutes.
Handle assembly for 125KT 175KT only.
ITEM PART NO. DESCRIPTION
1 M4365 Handle, Front
2 M4338 Handle, Rear
3 M4339 Wheel Support Frame
4 M6977 Machine Screw Blk (long)
5 M6037 Kep Nut Blk
6 M8746 Axle
7 M8752 Wheel
8 M8751 Cap
9 M8748 Spacer
10 M8747 Washer, Small
11 M8749 Washer, Large
12 M8750 Cotter Pin
13 M8754 Ext. Cord Caddy
14 M7336 Machine Screw Blk (Small)
Operating Instructions and Owner's Manual
QTY
1
1
1
8
12
1
2
2
2
4
2
2
2
4