Table des Matières
Publicité
Schleicher International
SCHALTBILD / WIRING DIAGRAM / PLAN DE MONTAGE / SCHAKELSCHEMA
DIAGRAMA ELÉCTRICO / ESQUEMA ELECTRICO / SCHEMA ELETTRICO
302/302CC // 402/402CC/402HS
16
GB
MAINTENANCE
COMPENSATION OF THE LIGHT BARRIER:
Note: If the compensation process has been
In order to eliminate malfunctions due to changing
interfered with due to exessive external incident
light conditions at the inlet aperture (e.g. by
light (direct sun light, lamps, spots etc.) or due to
changing the location) or due to the wear of the
a false procedure, keep the external light away
fotocell (scratches), the sensitivity of the light
from light barrier and re-start the compensation
barrier is automatically re-adjusted by the machine
process right from the beginning.
for the detection of "normal" paper in regular
intervals.
CLEANING THE PHOTOCELLS:
This so called "compensation" can also be carried
If paper particles should come to rest in the inlet
out manually in accordance with the sequence
guide (for example after a paper jam) it is possible
described in the following (e. g. after change of the
that the machine will not turn off, due to the broken
light barrier or the PC Board).
light barrier.
The "receptacle full" switch-off must not be
To remove these paper strips and also to clean
activated for the re-adjustment. The procedure is
the photocell, pass another sheet of paper through
as follows:
the feed slot, or switch the machine to reverse and
1. Switch off the maschine at the pushbutton
wipe both „eyes" of the photocell with a brush.
switch (1) and open the door.
2. Press the pushbutton switch "reverse" (3) and
MAINTENANCE CUTTING BLOCK:
keep it pressed.
(1.9x15 mm, 3.8x24 mm and 0.8x12 mm)
3. Press the "ready" pushbutton switch (1).
After approximately 30 minutes of continuous
4. Release the "reverse" pushbutton switch (3)
use, run the cutting system in reverse for 15 to 20
after approx. 3 sec.
seconds and spray some of the enclosed Special
5. (This process is only required for the cross-cut
Oil onto the cutting system.
models. (CC/HS/SX))
Push switching flap „receptacle full" backwards
TIP FOR ENERGY SAVING:
for at least 3 sec.
Please make sure that the shredder is switched
6. Close the door after approx. 3 sec.
off over night (pushbutton switch (1) (fig. 1).
7. Cover the light barrier with a piece of paper (do
not feed the paper up to the cutter) and wait until
the motor is switched on.
This completes the compensation. The machine
is now ready for operation.
MALFUNCTIONS
PAPER JAM:
Allow the motor to cool down for 15 to 20 minutes
If too much paper is fed to the cutting system the
(depending upon room temperature) and then
machine will react as follows:
continue shredding.
- a) 1.9 mm / 3.8 mm / 5.8 mm
The cutting system blocks and then stops.
CHECKLIST IN CASE OF MALFUNCTIONS:
b) 3.8x24 mm / 1.9x15 / 0.8x12 mm
If the device does not function, check the following:
The cutting system blocks, reverses a bit to
- Is the plug connected to the mains?
release the paper and then stops.
Mains connection: 2-pole mains switch,
- The motor shuts down automatically.
- The pilot lamp (6) (fig. 1) lights up.
Proceed as follows:
- Is the pushbutton switch (1) on?
- Briefly operate the pushbutton switch for reverse
- Is the door closed?
(3) (fig. 1).
- Is the receptacle full?
- The pilot lamp (6) (fig. 1) goes off.
The receptacle has to be emptied.
- Remove excess paper from the machine and
- Is there a paper jam?
continue shredding with less paper.
Follow the instructions under „paper jam".
- has the motor been overloaded?
MOTOR PROTECTION:
Wait until the motor has cooled, and then restart.
The motor shuts down automatically, should it
become overloaded. Turn the machine off with
If none of the above applies, please contact
the pushbutton switch (1) (fig. 1).
your dealer.
ACCESSORIES
Description
Plastic bag, 300 x 300 x 700 x 0,018 mm (302/-CC // 402/-CC/-HS)
Plastic bag, 440 x 330 x 950 x 0,05 mm (502/-CC/-HS)
Plastic bag, 600 x 500 x 1000 x 0,05 mm (452/-CC // 602/-CC/-HS // 007SX)
Lubricant, 125 ml bottle (CC/HS/SX)
Feeding mechanism for computer paper (452/-CC // 602/-CC/-HS // 007SX)
Note: For orders of special accessories and spare parts, please contact your dealer.
Schleicher International
TECHNICAL DATA
Cutting width:
302/402:
1.9 mm (strips)
302/402/452/502/602:
3.8 mm (strips)
302/402/502/602:
5.8 mm (strips)
302CC/402CC/
452CC/502CC/602CC:
1.9x15 mm (cross-cut)
302CC/402CC/
502CC/602CC:
3.8x24 mm (cross-cut)
402HS/502HS/
602HS/007SX:
0.8x12 mm
(high security)
Cutting capacity:
302/402:
1.9 mm:
12-14 sheets (70g/m
3.8 mm:
17-19 sheets (70g/m
5.8 mm:
21-23 sheets (70g/m
302CC/402CC:
1.9x15 mm:
7-9 sheets (70g/m
3.8x24 mm:
12-14 sheets (70g/m
402HS:
4-5 sheets (70g/m
452:
15-17 sheets (70g/m
452CC:
10-12 sheets (70g/m
502:
3.8 mm:
23-25 sheets (70g/m
5.8 mm:
31-33 sheets (70g/m
502CC:
1.9x15 mm:
13-15 sheets (70g/m
3.8x24 mm:
16-18 sheets (70g/m
502HS:
8-10 sheets (70g/m
602:
3.8 mm:
23-25 sheets (70g/m
5.8 mm:
27-33 sheets (70g/m
602CC:
1.9x15 mm:
13-16 sheets (70g/m
3.8x24 mm:
16-19 sheets (70g/m
602HS:
8-10 sheets (70g/m
007SX:
15-17 sheets (70g/m
Supply voltage:
230V/50Hz
240V/50Hz
120V/60Hz
100V/50/60Hz
Pre-fusing:
230V/240V/50Hz:
10 amps (slow-blow)
120V/100V/50/60Hz:
20 amps (slow-blow)
Working width:
260 mm
302/302CC:
240 mm
402/402CC/402HS:
240 mm
internal appliance plug,
452/452CC:
405 mm
separate power cord
502/502CC/502HS:
260 mm
602/602CC/602HS:
405 mm
007SX:
405 mm
Noise level:
approx. 54 dB(A)
Power:
302/302CC:
0.47 kW
402/402CC/402HS:
0.47 kW
452/452CC:
1.1/0.9 kW
502/502CC/502HS:
1.1 kW
602/602CC/602HS:
1.1 kW
007SX:
1.1 kW
Dimensions (WxDxH):
302/302CC:
385x280x635 mm
402/402CC/402HS:
385x280x740 mm
452/452CC:
660x430x880 mm
502/502CC/502HS:
490x380x870 mm
602/602CC/602HS:
660x430x1020 mm
007SX:
660x500x1020 mm
Order-No.
Weight:
99925
302/302CC:
ca. 18.5/20 kg
99977
402/402CC/402HS:
ca. 19.5/21/21 kg
452/452CC:
ca. 60 kg
99952
502/502CC/502HS:
ca. 41/43/43 kg
99943
602/602CC/602HS:
ca. 60 kg
81942
007SX:
ca. 93 kg
5
2
)
2
)
2
)
2
)
2
)
2
)
2
)
2
)
2
)
2
)
2
)
2
)
2
)
2
)
2
)
2
)
2
)
2
)
2
)
Publicité
Table des Matières
