Connecting And Charging - Braun Oral-B BLACK 7000 Mode D'emploi

English
Important Information
• Your Oral-B 5000–7000 can be used with an
interactive wireless display (i) and/or with your
Smart Phone (find details under «Connecting
your toothbrush to your Smart Phone»).
• To avoid electromagnetic interference and/or
compatibility conflicts, deactivate the radio
transmission of your toothbrush handle (e) before
using it in restricted surroundings, such as
aircrafts or specially marked areas in hospitals.
• Deactivate radio transmission by simultaneously
pressing the on/off (c) and mode button (d) for
3 seconds until the radio transmission display (f)
goes off. Follow the same procedure to reacti-
vate transmission again.
• Persons with pacemakers should always keep
the toothbrush more than six inches (15 centi-
meters) from the pacemaker while turned on.
Anytime you suspect interference is taking
place, deactivate the radio transmission of your
toothbrush.
Description
a Brush head
b Pressure sensor light (red) / visual timer light
(green)
c On/off button
d Brushing mode button
e Handle
f Radio transmission display (with Bluetooth
wireless technology)
g Charge level display
h Charging unit (basic charger and brush head
compartment with protective cover)
i SmartGuide (depending on model)
j SmartGuide holder (depending on model)
k Wall mount (depending on model)
l Adhesive ring (depending on model)
m Travel case (depending on model)
n Travel charger pouch (depending on model)
Specification
For voltage specifications refer to the bottom of the
charging unit.

Connecting and charging

Your toothbrush has a waterproof handle, is electri-
cally safe and designed for use in the bathroom.
• Plug the charger (h) into an electrical outlet and
place the toothbrush handle (e) on the charging
unit.
• The flashing blue lights indicate that the toothbrush
is charging (picture 1, page 5); once it is fully
charged, the lights turn off. A full charge can take
All manuals and user guides at all-guides.com
• If the rechargeable battery is low a blue light is
• For everyday use, the toothbrush handle can be
SmartGuide adjustments
(depending on model)
The SmartGuide (i) comes with a demonstration
mode. Deactivate this mode by removing the
compartment cover in the back (picture A, page 4)
and push the «set» or «h/min» button.
A flashing «12:00» indicates that you can now adjust
the clock time.
Note: If the SmartGuide display is blank before first
use (no active demonstration mode / no batteries
inserted) the batteries will need to be replaced/
®
inserted before continuing.
Batteries are supplied.
Clock Time
Press and hold the «set» button until «12h» is
displayed. By briefly pressing the «h/min» button,
you can toggle between «12h» or «24h» daytime
format. Push «set» to confirm your choice. Then
the hour digit starts flashing. Press the «h/min»
button until the right hour appears and confirm with
«set». Proceed same way to set both minute digits
(picture B, page 4).
up to 24 hours and enables up to ten days of
regular brushing (twice a day, 2 minutes).
Note: After deep discharge, the blue lights might
not flash immediately; it can take up to 10–15
minutes.
flashing on the charge level display (g) for some
seconds when turning your toothbrush on/off. If the
rechargeable battery is empty the motor will stop
and an orange light is flashing on the charge level
display; it will need a 40-minute charge before you
can use it for a 2-minute brushing.
stored on the charging unit to maintain it at full
power. Overcharging is impossible. To maintain
the maximum capacity of the rechargeable battery,
unplug the charging unit and fully discharge the
handle with regular use at least every 6 months.
7