Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
Control Unit (CU)
•
Refer to the vehicle installation drawings or experienced advice when determining the location
Refer to the vehicle installation drawings or experienced advice when determining the location
of the control unit. The control unit should not be close to potential sources of interference
of the control unit. The control unit should not be close to potential sources of interference,
e.g. cable bundles, exhaust pipe....
•
Make sure the power cables of the control unit are easily accessible.
•
Use the included double sided adhesive tape to fix the control unit to the cars' interior.
Use the included double sided adhesive tape to fix the control unit to the cars' interior.
Display unit
•
The display unit should be mounted on the dashboard with the included mounting bracket.
Make sure that the display is readable under all conditions.
•
Guide the cable towards the CU.
•
Plug the connector into the CU. The connector fits only one way, do not force.
Plug the connector into the CU. The connector fits only one way, do not force.
Cabling/connections
•
Every sensor cable has a letter written on it.
•
Plug each sensor cable into the corresponding port on the CU.
Connecting power CU
•
The CU gets power from the reverse light circuit of the vehicle. Use the red/black power cable
The CU gets power from the reverse light circuit of the vehicle. Use the red/black power cable
and the included cable clips to make the connections.
•
Locate the +12V power cable of the reverse light circuit and guide it through a cable clip.
Locate the +12V power cable of the reverse light circuit and guide it through a cable clip.
•
Insert the red cable of the CU power cable in that cable clip and press the metal part of the
Insert the red cable of the CU power cable in that cable clip and press the metal part of the
clip tightly. Close the cable clip.
•
Locate the GND cable of the reverse light circuit and guide it through a cable clip.
e GND cable of the reverse light circuit and guide it through a cable clip.
•
Insert the black cable of the CU power cable in that cable clip and press the metal part of the
Insert the black cable of the CU power cable in that cable clip and press the metal part of the
clip tightly. Close the cable clip.
•
Connect the power cable to the CU.
7. Operation
Warning mode
•
Following is an overview of the warning zones.
Warning zone
Danger zone
Caution zone
Safety zone
Beware of the blind zone behind the vehicle! Obstacles located inside the blind
zone will NOT be detected! The blind zone behind the vehicle is 30cm.
•
When an obstacle is detected in a warning zone, visual and audible warnings are given on the
When an obstacle is detected in a warning zone, visual and audible warnings are given on the
display unit.
•
Visual warnings are given by flashing of the display indicator [A]of the sensor(s) that detected
the obstacle, as well as a numeric display of the distance in meter [B]
Note: when an obstacle is detected by sensor A or B, the left indicator will flash, when detected
by sensor C or D, the right indicator will flash.
•
The time interval between the beeps is an indication of the distance to the obstacle. The
The time interval between the beeps is an indication of the distance to the obstacle. The
shorter the interval, the closer the obstacle. See the table below for an overview.
•
When multiple obstacles are detected, the display indicators of the sensors will flash, but only
When multiple obstacles are detected, the display indicators of the sensors will flash, but only
the distance to the obstacle located inside the highest priority warning zone and the
the distance to the obstacle located inside the highest priority warning zone and the
accompanying audible warnings are given.
•
The audible warnings can be disabled with the switch [C] on the LCD.
31.07.2014
All manuals and user guides at all-guides.com
SPBS10
dashboard with the included mounting bracket.
Distance D (m)
D ≤ 0.2
0.3 < D ≤ 0.4
0.5 < D ≤ 0.9
1.0 < D ≤ 1.5
1.6 < D ≤ 2.0
behind the vehicle! Obstacles located inside the blind
The blind zone behind the vehicle is 30cm.
6
Audible signal
Audible signal
Bi................
Bi................
Bi.Bi.Bi
Bi.Bi.Bi
Bi..Bi..Bi
Bi..Bi..Bi
Bi.....Bi.....Bi
Bi.....Bi.....Bi
-
-
of the sensor(s) that detected
[B] and a bar graph [E].
, the left indicator will flash, when detected
or an overview.
©Velleman nv
Publicité
Table des Matières
