Télécharger
Partager
Imprimer la page
  1. Manuels
  2. Marques
  3. Uline Manuels
  4. Pompes
  5. H-4377
  6. Mode d'emploi

Uline H-4377 Mode D'emploi

Masquer les pouces
1
2
3
4
5
6

Publicité

Les langues disponibles

Les langues disponibles

Liens rapides

Télécharger ce manuel
H-4377
ROTARY DRUM PUMP
TOOLS NEEDED
1/2" (13 mm) Wrench
IMPORTANT! This pump is made out of polypropylene, PVDF, PTFE, 304 stainless steel and EPDM. Use chemicals
compatible with these materials and follow OSHA guidelines when using this pump, including proper
grounding and protective gear as required. Unit not UL or FM approved.
1.
Rotate handle clockwise several times to prime. If
unit does not prime after a few turns, pouring some
fluid into pump inlet may help free pump.
2. For siphoning, position handle straight down.
3. To stop siphoning, rotate handle 1/4 turn (leave
handle in horizontal position).
PAGE 1 OF 6
1-800-295-5510
uline.com
Flathead Screwdriver
SPECIFICATIONS
Pump Type
Flow
Maximum Fluid Temperature
Bung Adapter
Suction Tube Length
Inlet
Outlet
Wetted Parts
Maximum Viscosity
OPERATING INSTRUCTIONS
Rotary - Vane
8 GPM (12 oz / Stroke)
130°F / 54°C
2" Male
40" Maximum
1⁄" O.D.
1" O.D. Curved Spout
PP, PVDF, PTFE, 304SS & EPDM
1,000 cps
4. After using pump, position handle straight down.
Liquid will drain back into the container.
5. If pump is removed from drum, rinse it thoroughly in
a liquid that is compatible with both the pump and
the fluid being pumped.
6. Regularly check pump and suction tubes for leaks.
Leaks in the suction line or in pump housing will
cause inefficient pumping and loss of prime.
Para Español, vea páginas 3-4.
Pour le français, consulter les pages 5-6.
0721 IH-4377

Publicité

loading

Manuels Connexes pour Uline H-4377

Sommaire des Matières pour Uline H-4377

  • Page 1 Para Español, vea páginas 3-4. Pour le français, consulter les pages 5-6. H-4377 1-800-295-5510 uline.com ROTARY DRUM PUMP TOOLS NEEDED 1/2" (13 mm) Wrench Flathead Screwdriver SPECIFICATIONS Pump Type Rotary - Vane Flow 8 GPM (12 oz / Stroke) Maximum Fluid Temperature 130°F / 54°C...

  • Page 2: Assembly And Installation

    4. Attach bung adapter (19) onto the top of the suction tube is at the desired depth in the drum and assembled suction tube. Screw assembled suction is not blocked. tube into pump body (1). 1-800-295-5510 uline.com PAGE 2 OF 6 0721 IH-4377...

  • Page 3: Herramientas Necesarias

    H-4377 800-295-5510 uline.mx BOMBA GIRATORIA PARA TAMBO HERRAMIENTAS NECESARIAS Llave de 13 mm (1/2") Desarmador de Cabeza Plana ESPECIFICACIONES Tipo de Bomba Giratoria - Aspas Flujo 8 GPM (12 oz / Bombeo) Temperatura Máxima de Fluido 54°C (130°F) Adaptador de Tapón Macho 5.1 cm (2")

  • Page 4: Ensamble E Instalación

    (1). esté a la profundidad deseada en el tambo y que no esté bloqueado. 800-295-5510 uline.mx PAGE 4 OF 6 0721 IH-4377...

  • Page 5: Pompe Rotative Pour Baril

    H-4377 1-800-295-5510 uline.ca POMPE ROTATIVE POUR BARIL OUTILS REQUIS Clé 13 mm (1/2 po) Tournevis à lame plate SPÉCIFICATIONS Type de pompe Rotative à palettes Débit 8 GPM (354,9 ml [12 oz] / tour de manivelle) Température maximale du liquide 54 °C/130 °F Adaptateur de bonde 51 mm (2 po) mâle...

  • Page 6: Assemblage Et Installation

    Vissez le tube bonde (19). Assurez-vous que le tube d'aspiration d'aspiration assemblé dans le corps de pompe (1). assemblé n'est pas obstrué et qu'il est inséré à la profondeur voulue dans le baril. 1-800-295-5510 uline.ca PAGE 6 OF 6 0721 IH-4377...