GE PDWF480PSS Manuel Du Propriétaire page 17

Problem Possible Causes
Spots and filming
Extremely hard water
on glasses and
Low inlet water temperature
flatware
Overloading the dishwasher
Improper loading
Old or damp powder detergent
Rinse agent dispenser empty
Too little detergent
Cloudiness on Combination of soft water and
glassware too much detergent
Water temperature entering
the dishwasher exceeds 150°F
Suds in the tub Correct detergent
wasn't used
Rinse agent was spilled
Detergent left in Dishes are blocking the
dispenser cups detergent cup
Water in the Cap not tightened after filling
SmartDispense ™ the dispenser
dispenser
Black or gray Aluminum utensils have
marks on dishes rubbed against dishes
Dishes don't dry Low inlet water temperature
Rinse agent dispenser is empty
Control panel responded Door latch may not be properly
to inputs but dishwasher seated
never filled with water Water valve may be turned off
Stained tub interior Some tomato-based foods can
cause reddish stains
Tea or coffee stains
An overall yellow or brown film can • A special filter in the water supply line is the only way to correct
be caused by iron deposits in water
White film on inside surface—
hard water minerals
What To Do
®
• Use Jet-Dry or Cascade Crystal Clear
prevent new film buildup.
• Make sure water temperature is at least 120°F.
• Load dishwasher as shown in the Loading Place Settings section.
• Make sure detergent is fresh.
• If water is extremely hard, a softener may be required.
• This is called etching and is permanent. To prevent this from happening,
use less detergent if you have soft water. Wash glassware in the shortest
cycle that will get them clean.
• This could be etching. Lower the water heater temperature.
• Use only automatic dishwasher detergents to avoid sudsing.
Cascade ® and Electrasol ® Automatic Dishwashing Detergents
have been approved for use in all GE dishwashers.
• To remove suds from the tub, open the dishwasher and let
suds dissipate. Close and latch the dishwasher door. Pump out water
by touching the START/RESET pad once; then 30 seconds later,
touch the START/RESET pad again. Repeat if necessary.
• Always wipe up rinse agent spills immediately.
• Reposition the dishes, so the water from the lower spray arm can
flush the detergent cup. See pages 13 and 14.
• Use a turkey baster to remove as much water as possible from the
SmartDispense ™ dispenser and refill it as normal. Be sure to tighten the
cap fully to prevent water from entering the dispenser.
• Remove marks with a mild, abrasive cleaner.
• Make sure inlet water temperature is at least 120°F.
• Select HEATED DRY.
• Use PRE-WASH or ADDED HEAT options.
• Select a higher cycle, such as ANTI-BACTERIA or COOKWARE.
• Check the rinse agent dispenser and fill as required.
• Make sure the door is firmly closed.
• Make sure water valve (usually located under the sink) is turned on.
• Use of the RINSE AND HOLD cycle after adding the dish to the load
can decrease the level of staining. GE recommends Cascade
Plastic Booster to help remove these types of stains.
• Remove the stain by hand, using a solution of 1/2 cup bleach
and 3 cups warm water.
WARNING
Before cleaning interior, wait at least 20 minutes after a cycle for the
heating elements to cool down. Failure to do so can result in burns.
this problem. Contact a water softener company.
®
• GE recommends Jet-Dry or Cascade Crystal Clear
prevent hard water mineral deposits from forming.
• Run dishwasher with citric acid to remove mineral deposits. Citric
acid (Part number: WD35X151) can be ordered through GE Parts.
See back cover for ordering information.
ge.com
® rinse agents to remove spots and
®
® to help
17