Publicité

Les langues disponibles

Les langues disponibles

Liens rapides

Installation Instructions
Built-In Dishwasher
If you have questions, call 800.GE.CARES (800.432.2737), 1-800-561-3344 or visit our
website at: www.ge.com, www.geappliances.ca, www.electromenagersge.ca
BEFORE YOU BEGIN
STOP
Read these instructions completely and
carefully.
IMPORTANT
– Observe all governing codes and
ordinances.
• Note to Installer – Be sure to leave these instructions for the
consumer's and local inspector's use.
• Note to Consumer – Keep these instructions with your
Owner's Manual for future reference.
• Skill Level – Installation of this dishwasher requires
basic mechanical, electrical and plumbing skills. Proper
installation is the responsibility of the installer. Product
failure due to improper installation is not covered under
the GE Appliance Warranty. See warranty information.
• Completion Time – 1 to 3 Hours. New installations require
more time than replacement installations.
IMPORTANT
– The dishwasher MUST be installed
to allow for future removal from the enclosure if service is
required.
If you received a damaged dishwasher, you should
immediately contact your dealer or builder.
Optional Accessories – See the Owner's Manual for available
custom panel kits.
Your dishwasher is a water heating appliance
FOR YOUR SAFETY
Read and observe all CAUTIONS and WARNINGS
shown throughout these instructions. While performing
installations described in this booklet, gloves and either
safety glasses or goggles should be worn.
READ CAREFULLY.
KEEP THESE INSTRUCTIONS.
31-31568 05-16 GE

Publicité

Table des Matières
loading

Sommaire des Matières pour GE PDW1860K01SS

  • Page 1 Installation Instructions Built-In Dishwasher If you have questions, call 800.GE.CARES (800.432.2737), 1-800-561-3344 or visit our website at: www.ge.com, www.geappliances.ca, www.electromenagersge.ca IMPORTANT – The dishwasher MUST be installed BEFORE YOU BEGIN to allow for future removal from the enclosure if service is...
  • Page 2: Installation Preparation

    Installation Preparation PARTS SUPPLIED: ■ Two #8 Phillips head wood screws, 5/8" long to secure dishwasher to underside of countertop (in literature package). 2 Wood Screws MATERIALS YOU WILL NEED: ■ Ferrule, compression nut and 90° Elbow (3/8" NPT external thread on one end, opposite end sized to fit water supply) ■...
  • Page 3: Prepare Dishwasher Enclosure

    Installation Preparation PREPARE DISHWASHER ENCLOSURE WARNING persons, the installer must ensure that the dishwasher is This Wall Area completely enclosed at the time of installation. must be Free of Pipes or wires CLEARANCES: When 34-1/2" ± 1/2" 24" installed into a corner, Underside of 5"...
  • Page 4: Prepare Electrical Wiring

    Installation Preparation PREPARE ELECTRICAL WIRING WARNING FOR PERSONAL SAFETY: Remove house fuse or open circuit breaker before beginning installation. Do not use 1-1/2” Dia. an extension cord or adapter plug with this Hole (Max.) appliance. 3” from Cabinet Electrical Requirements •...
  • Page 5: Installation Instructions

    Installation Instructions PREPARE HOT WATER LINE BEFORE YOU BEGIN Locate and set aside the package containing shaded area shown in Figure F. STOP 2 Phillips head countertop mounting screws • The line may pass through the same hole as the electrical and 2 additional toekick screws (located in cable and drain hose.
  • Page 6 Skip this step if dishwasher will be direct wired. lay it on its back. Use Power Cord Kit WX09X70910, available for purchase from an authorized GE Appliance Dealer. The power cord and connections must comply with the National Electrical Code, Section 422 and/or local codes and ordinances.
  • Page 7 Installation Instructions STEP 6 POSITION WATER LINE AND STEP 8 SLIDE DISHWASHER PARTIALLY HOUSE WIRING INTO CABINET DO NOT PUSH AGAINST FRONT PANEL WITH KNEES. the opening to avoid interference with base of dishwasher DAMAGE WILL OCCUR. and components under dishwasher. •...
  • Page 8: Top View

    Installation Instructions STEP 9 POSITION DISHWASHER UNDER COUNTERTOP • Push the dishwasher into the cabinet. • Push the sides with your hands. Do not use your knee against the door since door damage will occur. • Check that the tub insulation blanket does not get “bunched-up”...
  • Page 9: Important

    Installation Instructions STEP 11 SECURE DISHWASHER TO STEP 10 LEVEL DISHWASHER COUNTERTOP OR CABINET IMPORTANT – Dishwasher must be level for proper In this step you will need Side-Mounting dish rack operation and wash performance. the 2 Phillips special head Bracket •...
  • Page 10 Installation Instructions STEP 12 CONNECT WATER SUPPLY DRAIN LINE INSTALLATION Connect water supply line to 90° elbow. • Connect drain line to air gap, waste tee or disposer using • Slide compression nut, then ferrule over end of water line. either previously determined method.
  • Page 11 Installation Instructions STEP 15 PRETEST CHECK LIST STEP 14 CONNECT POWER SUPPLY Review this list after installing your dishwasher to avoid Skip this step if equipped with power cord. charges for a service call that is not covered by your warranty.
  • Page 12 Installation Instructions STEP 16 DISHWASHER WET TEST STEP 17 REPLACE TOEKICK ■ Turn on power supply (or plug power cord into outlet, if equipped). ■ Start the unit to check for leaks. – Press ON/OFF button to turn unit on –...
  • Page 13: Lave-Vaisselle Encastré

    Instructions d’installation Lave-vaisselle encastré En cas de question, appeler 800.GE.CARES (800.432.2737), 1-800-561-3344 ou rendre visite à notre site web : www.ge.com, www.geappliances.ca, www.electromenagersge.ca IMPORTANT AVANT DE COMMENCER – Le lave-vaisselle DOIT être installé de ARRÊT Il faut lire soigneusement toutes ces instructions.
  • Page 14: Préparation Pour L'installation

    Préparation pour l’installation PIÈCES FOURNIES : ■ Deux (2) vis à bois à tête cruciforme n° 8 de 5/8 po de long pour fixer le lave-vaisselle au-dessous du 2 vis à bois plan de travail (inclus dans la documentation). MATÉRIAUX NÉCESSAIRES : ■...
  • Page 15: Préparation De L'enceinte Du Lave-Vaisselle

    Préparation pour l’installation • Le lave-vaisselle doit être installé de manière que le tuyau de PRÉPARATION DE L’ENCEINTE DU LAVE-VAISSELLE d’obtenir un bon écoulement. ATTENTION Cette portion du mur ne doit pas avoir Pour réduire le risque de choc électrique, d’incendie ou de 61 cm de tuyaux blessures, l’installateur doit s’assurer, au moment de l’installation,...
  • Page 16: Préparation Pour Le Branchement Électrique

    Préparation pour l’installation PRÉPARATION POUR LE BRANCHEMENT ÉLECTRIQUE ATTENTION SÉCURITÉ : Enlever le fusible du circuit ou déclencher le disjoncteur avant Trou de 38 mm (1-1/2 po) de commencer l’installation. Avec cet de diamètre, maximum appareil, ne pas utiliser une rallonge ou un adaptateur de prise.
  • Page 17: Préparation Du Tuyau D'eau Chaude

    Instructions d’installation PRÉPARATION DU TUYAU D’EAU CHAUDE AVANT DE COMMENCER ARRÊT Placer à portée de main le sachet contenant • Le tuyau peut passer dans le même trou que le câble deux vis à tête cruciforme pour le montage du électrique et le tuyau de vidange.
  • Page 18: Étape 4 : Installation Du Cordon D'alimentation

    Ignorer cette étape si le lave-vaisselle est branché directement • Amener le lave-vaisselle à proximité de l’emplacement vente chez les distributeurs agréés d’appareils ménagers GE. Le cordon d’alimentation et les branchements doivent être conformes au code national d’électricité et aux codes et règlements locaux.
  • Page 19: Étape 7 : Installation Du Tuyau De Vidange Dans L'armoire

    Instructions d’installation ÉTAPE 6 : MISE EN PLACE DU TUYAU D’EAU ÉTAPE 8 : GLISSER LE LAVE-VAISSELLE ET DES FILS DE LA MAISON PARTIELLEMENT DANS L’OUVERTURE DE L’ARMOIRE NE PAS POUSSER CONTRE LE PANNEAU AVANT AVEC LE base du lave-vaisselle et des divers éléments sous celui-ci. GENOU.
  • Page 20: Étape 9 : Mise En Position Du Lave- Vaisselle Sous Le Plan De Travail

    Instructions d’installation ÉTAPE 9 : MISE EN POSITION DU LAVE- VAISSELLE SOUS LE PLAN DE TRAVAIL Pour changer la position du lave-vaisselle, prendre • Pousser le lave-vaisselle dans l’armoire. les deux côtés avec les mains. contre la porte, car ceci endommage la porte. couverture isolante du bac n’est pas «...
  • Page 21: Étape 10 : Mise À Niveau Du Lave-Vaisselle

    Instructions d’installation ÉTAPE 10 : MISE À NIVEAU DU ÉTAPE 11 : FIXATION DU LAVE-VAISSELLE À LAVE-VAISSELLE L’ARMOIRE À cette étape, il faut les IMPORTANT – Le lave-vaisselle doit être de niveau 2 vis spéciales à tête Pattes de montage latéral pour obtenir un bon déplacement de l’égouttoir et du lave- cruciforme mises de vaisselle.
  • Page 22: Étape 12 : Branchement De L'alimentation D'eau

    Instructions d’installation ÉTAPE 12 : BRANCHEMENT DE INSTALLATION DU TUYAU DE VIDANGE L’ALIMENTATION D’EAU • Brancher le tuyau de vidange sur le dispositif anti-siphon, le raccord en té d’égout ou le broyeur à déchets, en utilisant la Brancher le tuyau d’alimentation d’eau au coude à angle droit. méthode indiquée précédemment.
  • Page 23: Étape 14 : Branchement De L'alimentation Électrique

    Instructions d’installation ÉTAPE 14 : BRANCHEMENT DE ÉTAPE 15 : LISTE DE VÉRIFICATION AVANT L’ALIMENTATION ÉLECTRIQUE DE FAIRE LES ESSAIS Ignorer cette étape si le lave-vaisselle est équipé d’un cordon Examiner cette liste après l’installation du lave-vaisselle pour éviter les frais d’intervention qui ne sont pas couverts •...
  • Page 24: Étape 16 : Essay Du Lave-Vaisselle Avec De L'eau

    Instructions d’installation ÉTAPE 16 : ESSAY DU LAVE-VAISSELLE AVEC ÉTAPE 17 : REPOSE DE LA PLINTHE DE L’EAU ■ Mettre le circuit sous tension (ou brancher le cordon d’alimentation dans la prise de courant, si installée). ■ Mettre le lave-vaisselle en marche pour vérifier qu’il n’y a pas de fuites.

Ce manuel est également adapté pour:

Pdw1800kwwPdw1800k01bb

Table des Matières