Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
English
and bike tires, balls, rafts, air mattresses, swimming pool
floats, etc. This product is intended for household, consumer
use only.
THIS PRODUCT USES THE BATTERY
AND CHARGER LISTED IN THE CHART
BELOW.
Description
20V Max* lithium-ion
Battery:
20V Max* lithium-ion
Battery Charger:
2 Amp Fast Charger:
ASSEMBLY AND ADJUSTMENTS
WARNING: To reduce the risk of serious personal
injury, turn unit off and disconnect it from
power source remove the battery pack before
making any adjustments or removing/installing
attachments or accessories. An accidental start-up
can cause injury.
12V Dc Cord Storage
•
Wrap the 12V DC cord around the cord retainer
located in the base of the inflator and snap the 12V
DC connector
into its storage location on the
14
cord retainer.
120V Ac Cord Storage
•
Coil the 120V AC cord into its storage location located
on the back of the inflator.
Air Hose Storage
•
The high-pressure hose
channel around the face of the unit. Wrap the high-
pressure hose inside the channel.
High-Volume Hose Storage
•
The high-volume hose
around the back of the unit. Wrap the high-volume hose
inside the channel.
Accessories Storage
•
The accessories
16
17
the unit inside the accessory storage area.
FITTING THE ACCESSORIES
Universal valve adapter (Fig. B)
Your inflator is supplied with the standard tapered nozzle
, a brass coupler
, and the inflator needle valve
18
17
located on the back of the unit.
•
To use the universal valve adaptor
lever is in the up position.
8
Catalog Number
ʵ LBXR20
ʵ LBXR20BT
ʵ LCS20
ʵ LCS201
ʵ LCS1620
ʵ L2AFC
ʵ L2AFCBST
ʵ LCS200
10
is located in a storage
is located in a storage channel
7
18
are stored in the back of
9
, make sure the
•
Place the valve adapter over the stem of the inflator
needle valve, brass coupler adaptor or tapered nozzle.
•
Press the lever
to lock it in place.
•
Place the inflator needle valve, brass coupler adapter or
tapered nozzle into the item to be inflated.
nOTE: Always make sure that the lever is in the up position
when not in use. Operate your inflator only with the
universal valve adaptor or with the included nozzles.
nOTE: Make sure the universal valve adapter is firmly
locked in place before turning the inflator on.
Figure B
16
17
18
high-volume hose (Fig. C)
•
Remove the high-volume hose
storage location.
•
Line up the notches
the high volume pump inflator connection
slide the hose on and twist counter-clockwise to secure.
•
To remove, twist the hose clockwise and slide hose off.
Figure C
Many inflatables have an internal flap that prevents air loss
during inflation, especially air mattresses. Unless this flap is
displaced by the nozzle the inflatable will not inflate. Push
the nozzle firmly into the valve to make sure that you push
this flap out of the way.
WARNING: Risk of Bursting. Excessive air pressure
may cause a hazardous risk of bursting or personal
injury. Check the manufacturer's maximum pressure
rating for items being inflated.
nOTE: If the pressure rating for the item being inflated
is above 100 psi, note that the maximum run time is 10
minutes, leave to rest for 20 minutes before reusing.
OPERATION
WARNING: To reduce the risk of serious personal
,
16
injury, turn unit off and disconnect it from power
source and remove the battery pack before
making any adjustments or removing/installing
attachments or accessories. An accidental start-up
can cause injury.
on the universal valve adapter down
19
19
7
from the
20
of the hose with the nubs
21
12
9
21
of
12
. Then,
20
7
Publicité
Table des Matières
