Description Of The Tool Indication; Remarks In Respect Of The Determined Use; Operation Of The Unit; Explanation Of The Application Range - Textron Klauke EK 120 U-L Mode D'emploi

Instruction Manual
EK 120 U-L
The new tools feature an integrated pressure sen-
sor which automatically identifi es the achieved crim-
ping force during every crimping operation. If a de-
viation from the set operation pressure is identifi ed,
an acoustic signal sounds and a red display fl ashes
(tab. 1).
A white LED illuminates the working space after ac-
tivating the trigger. It automatically switches off 10
sec. after releasing the trigger. This feature can be
deactivated.
Through an optional USB adapter a report can be
generated at the end of a working session at a PC
documenting the proper function of the tool.
The compact ergonomically formed design consists
2K
of 2 components. The grip area is rubber coated
and therefore slip resistent. The housing design is
optimized in respect of the center of gravity which
improves the handling and supports fatique-proof
working.
All tool functions can be controlled by one trigger.
This results in an easy handling and a better grip
compared to a two button operation.
Li-Ion batteries do neither have a memory effect nor
self discharge. Even after long periods of non ope-
ration the tool is always ready to operate. In addition
we see a lower power weight ratio with 50% more
capacity and shorter charging cycles compared to
NiMH batteries.
The oil used in our tool is particularly environmen-
tally friendly and and has been rewarded
Angel". The oil is also suitable for low temperatures
and has excellent lubrication characteristics.

3.3 Description of the tool indication

See Tab. 1.
Prior to operating the unit the charging level of the battery
(pic. 1.2) should have been tested2. A low charging level
can be detected by the fl ashing of the LED (pic. 1.1) for
20 s at the end of a crimping cycle.
HE.13447 © 11/2009
All manuals and user guides at all-guides.com
„The Blue
4. Remarks in respect of the determi-
ned use
Before starting any work on electrical appliances it must
be safeguarded that there are no live parts in the imme-
diate assembly area of the user. If this not possible spe-
cial precaution measures (
e.g. acc. to EN 50110-1
near live parts must be provided.
Keep your working area clean and tidy. Do not use this
tool when you are tired, on drugs, had alcohol or if you
are medicated.

4.1 Operation of the unit

Cycle: see pictures in front
When performing deep indent crimps the die-holder must
be replaced against the connector cage of the deep in-
dent crimp set. On the opposite side the indenter must be
set into the adapter (pic. 16).

4.2 Explanation of the application range

The electric hydraulic unit can be operated with a large
number of various crimping dies.
Attention
Do only crimp those connecting materials men-
tioned in Tab. 2.
If different conducting materials have to be crimped, ple-
ase contact the manufacturer.
The deep indent crimping is performed according to the
French Standard C 33-090-4.
Attention
Do not crimp on live cables or conduc-
tors
The unit is a hand held tool and it is not supposed to be
restrained in a vise. It is not allowed to use the tool in a
stationary application.
The tool is not designed for continued operations. After
a sequence of approximately 40 completed cycles you
have to make a break of 15 min. to give the tool time to
cool down.
Attention
Too intensive use can cause heat damages for
the tool
Attention
During the operation of electric engines sparks
can occur which might ignite highly infl ammab-
le or explosive liquids and materials
Attention
Electric-hydraulic tools should not be operated
in pouring rain or under water.

4.3 Mounting instructions

Please read the assembly instructions in our general ca-
talogue.
Attention
Even if the code number is identical only those
dies should be used which are suitable for the
material.
) for working
2
GB