KORTING HI 6450 RI Notice D'utilisation page 31

- The hob is equipped with a pan sensor; when the pan is
removed or badly positioned, the
If, on the other hand, the surface of the glass is still hot, the
symbol will appear alternating with the
The hob is equipped with a safety system which moves all
hotplates to the OFF position and activates the
when liquids or items are detected on the control panel.
These symbols will flash on the display:
be deactivated by removing the item or the liquid. The hob
will switch off automatically.
When the hob switches on, the timer display Q stays on at the
value . If the function is not activated, after a few seconds
the display Q shows nothing.
Note: the Timer can be activated on all the cooking zones
simultaneously.
This function allows to establish the time (from 1 to 99
minutes) or automatic switch-off of the cooking zone selected.
Activation:
1- Select the cooking zone (E).
2- Set the cooking level (from 1 to 9) desired, by acting on the
SLIDER control (D1).
3- Press the Timer button (N), the display will show
this point, the hob indicator (O) with the timer function active,
starts to flash.
4- Set the unit time (N2) desired from 0 to 9 by acting on the
SLIDER control (D1) e.g.
5- After a few seconds the unit value (N2) and the tenths (N1)
will appear fixed on the display
- if you want to set a time exceeding 9 minutes e.g:
just run your finger over the SLIDER control (D1).
- if, on the contrary, no operation is performed, it stops
flashing after a few seconds and the Timer display (Q) will
show the cooking time previously set
6- At the end of the programmed time, the timer display (Q)
and the hob indicator (O) will start to flash followed by an
acoustic sound.
To deactivate the acoustic signal just press the timer button
N, otherwise it will deactivate automatically after 2 minutes.
To deactivate the timer function before the set time:
- Select the zone (E) and press one of the two buttons
(N). When the zone indicator (R) on display (E) stops flashing,
the function is no longer active.
Note: to display the residual cooking time, just press the
zone (E) of interest selection button.
zone (E) has the Timer inserted.
- The Minute Minder allows to set an established countdown
that goes from 1 to 99 minutes.
On expiry of the time, the hob emits an acoustic signal without
changing the active functions.
- The function activates only if the cooking level is set at "0"
on all displays (R).
- Press the Timer button (N) and set the time with the same
procedure as the Timer function, with the unique exception
that the indicators (O) do not switch on.
symbol will appear.
.
. They can
.
;
.
Note: whenever the Timer is to be activated on at least one
zone, the Minute Minder deactivates automatically.
1- Use one of the buttons to select (E) the cooking zone where
the timer function is to be activated.
2- Set the cooking level by acting on the SLIDER control (D1).
3- Select the Timer button (N).
4- Select the button (E) again where the timer function is to
be activated.
5- Select the Timer button (N).
6- Set the cooking time by acting on the SLIDER control (D1).
Depending on the appliance model, it may be fitted with a
Booster system which can be used to speed up cooking times
through the application of a power level which is greater than
the nominal value, within a defined period of time.
The cooking areas provided with this function are indicated
by a letter (Z).
To activate the Booster, switch the interested cooking area on
at any power level and press key S (Fig.2 - Fig.3). This allows
to reach higher temperatures in a short time disbursing the
maximum power possible.
The letter P on the display indicates that the function is active.
This will be displayed for about 10 minutes, then the cooking
area will automatically turn back to power level 9.
- The Booster may not activate if, the cooking zone (with the
letter Z) has been previously activated with high temperature
levels.
, At
- In order to use the Booster function, wait for the P on the
display R to stop flashing and the temperature inside the
cooking surface to decrease.
Each phase (this is divided into two zones in a vertical line:
F1 e F2) is capable of using a maximum power of 3,700W.
If this is exceeded for example by activating the Booster,
,
the software automatically lowers power of the previously
selected zone until it reaches the allowed power level.
The display of the zone with limited power will begin to lash
for about 3 seconds. During this time it is possible to modify
the power level.
The Heat up function can be used to set the cooking zone
to its maximum temperature for a specified period of time,
after which the temperature will return to a lower value set
previously.
To activate the Heat up function, select one of the
zones (E).
Set the cooking level at "9" by acting on the SLIDER control
(D1), press Heat up (L1)and the
letter "A". This means that the (Heat up) function is active.
Set the desired
zone display will now show the letter "A" and the desired
cooking level (e.g. 6) alternately.
level variation is made, the indicator (D2)
- If no
switches off.
Note: it is possible ONLY to increase the previously-set
cooking level:
1- Select the
active.
2- Increase the desired temperature by running your finger
over the SLIDER control (D1).
When the Heat up function has finished running, the hob will
emit a sound signal or BEEP; the relevant
- 31 -
zone will show the
(between 1 and 8); the
zone (E) where the Heat up function is
will