Publicité
Les langues disponibles
Les langues disponibles
Liens rapides
Hitch Shown In Proper Position
Equipment Required:
Fastener Kit: 36416F
Wrenches: 10mm, 12mm, 14mm, 17mm
Drill Bits: 1/2"
Hitch Requires 1/2" pin and clip.
Toyota Camry Hybrid:
Remove plastic fascia covering the side frame
rail of the vehicle. Return plastic fascia covering
and screws to vehicle owner
1
Qty. (4)
M10 X 40 X 1.25 CL8.8 Hex Bolt
2
Qty. (4)
3/8" Conical Toothed Washer
3
Qty. (2)
1/2-13 X 2.00 GR 5 Hex Bolt
1.
Remove spare tire from the inside of the trunk of the vehicle.
2.
Lower vehicle exhaust by removing the rubber exhaust hangers.
3.
Remove fascia rivets from the fascia tabs between the trunk pan of the vehicle and the rear fascia. If present, remove the
plastic under covering located under the trunk pan.
4.
Remove the existing bracket shown in Figure 2 from the driver's side vehicle frame rail and the rear end panel and return to
vehicle owner.
5.
Raise hitch into position and install the M10 Hex bolts and the 3/8" conical toothed washers into the existing weldnuts in the
vehicle.
6.
Using the hitch as a template, drill two holes through the trunk pan of the vehicle.
7.
From the inside of the trunk, scrape the foam rubber material away from the inside surface of the trunk pan around the holes
drilled in step 5.
8.
Install the 1/2" hex bolts, blocks, lockwashers and nuts as shown above.
9.
Reinstall the spare tire inside the trunk.
10.
Reattach the rubber exhaust hangers, and insert the fascia rivets back into to the fascia tabs removed in step 3.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to
prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working
beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5
and SAE J684.
z
2006 Cequent Towing Products
Installation Instructions
Toyota Camry Hybrid
Fascia
Drawbar Kit:
Drawbar must be used in the
Rise position only.
Trunk Pan
Fastener and
bracket
location see
Figure 2.
Tighten all M10 CL8.8 fasteners with torque wrench to 42 Lb.-Ft. (57 N*M)
Tighten all 1/2-13 GR5 fasteners with torque wrench to 75 Lb.-Ft. (102 N*M)
Toyota Camry
36071
Wiring Access Location: PC3, PC4
4
Qty. (4)
5
Qty. (2)
6
Qty. (2)
Sheet 1 of 3
Do Not Exceed Lower of Towing Vehicle
Manufacturer's Rating or
3500 lb, 1589 kg Max Gross Trailer Weight
300 lb, 136 kg Max Tongue Weight
Frame Rail
Bracket Removed in
installation step 4.
Block 1/4 X 1.50 X 3.00
1/2" Lockwasher
1/2" Hex Nut
36416N
9-6-06
Part Numbers:
36416
90152
06397
Rear End Panel
Existing
Weldnuts
Figure 2
Rev. B
Publicité
Manuels Connexes pour Cequent Towing Products 90152
Sommaire des Matières pour Cequent Towing Products 90152
- Page 1 Do not cut access or attachment holes with a torch. This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684. Sheet 1 of 3 36416N 9-6-06 Rev. B 2006 Cequent Towing Products...
- Page 2 Ce produit est conforme aux normes V-5 et SAE J684 de la V.E.S.C. (État de New York) concernant les spécifications en matière de sécurité des systèmes d’attelage. Feuille 2 de 3 36416N 9-6-06 Rev. B 2006 Cequent Towing Products...
- Page 3 Este producto cumple con las especificaciones y requisitos de seguridad para conectar dispositivos y sistemas de remolque del estado de Nueva York, V.E.S.C. Regulación V-5 y SAE J684 Página 3 de 3 36416N 9-6-06 Rev. B 2006 Cequent Towing Products...