Publicité
Les langues disponibles
Les langues disponibles
Liens rapides
Flyware Bracket System
Y orkville FH1
This hardware kit has been specifically designed to expand your enclosure's already
advanced mounting capabilities.
IMPORTANT!! The rigging of loudspeaker systems is an extremely serious matter. Overhead rigging
requires extensive experience, including (but not limited to) calculating working load limits, hardware instal-
lation, and periodic safety inspection of all hardware and cabinetry. If you lack these qualifications, do not
attempt the installation yourself, but instead use a professional structural rigger. Improper installation can
result in bodily injury or death. Consult a structural engineer to calculate added loads upon the building.
Structural reinforcement may be necessary to insure a safe installation.
The FH1 System
The FH1 installation system has been developed to expand the ver-
satility and simplicity of installing enclosures in multi-box arrays.
The FH1 kit allows enclosures to be mounted in two or
more cabinet arrays with greater ease than employing
individual three-point hangs for each cabinet. (An ardu-
ous chore when attempting to install clusters of loud-
speakers using standard eyebolts, shackles and
cables. The FH1 is easily mounted strategically to
the top and bottom of the enclosure.
Flying Arrays
A single FH1 kit allows a pair of cabinets to be
clustered in a tight-pack array at their optimum
splay and more can be attached together for larg-
er clusters (3 or more enclosures).
Z761 x 2
Z762 x 2
Kit Includes
2 Z761 Cross Member Supports
2 Z762 Shackle Cross Members
4 Z763 Support Plates
8 YS#8920 3/8-16 X 2 HH GRD 5 ZP BOLT
4 YS#8996 3/8-INCH SPLIT WASHER BLACK
Canada
Voice: (905) 837-8481
Fax: (905) 837-8746
Yorkville Sound
550 Granite Court
Pickering, Ontario
L1W-3Y8 CANADA
1
Z763 x 4
U.S.A.
Voice: (716) 297-2920
Fax: (716) 297-3689
w w w . y o r k v i l l e . c o m
Yorkville Sound Inc.
4625 Witmer Industrial Estate
Niagara Falls, New York
14305 USA
YS#8920 x 8
Publicité
Manuels Connexes pour YORKVILLE FH1
Sommaire des Matières pour YORKVILLE FH1
- Page 1 Structural reinforcement may be necessary to insure a safe installation. The FH1 System The FH1 installation system has been developed to expand the ver- satility and simplicity of installing enclosures in multi-box arrays. The FH1 kit allows enclosures to be mounted in two or more cabinet arrays with greater ease than employing individual three-point hangs for each cabinet.
- Page 2 Shackle Cross Members and the Cross Member Support (as shown in figure 2c). Tip: it’s easiest to assemble FH1 Bracket apart from the enclosure, either on a table or the top of the enclo- sure. Use the supplied bolts to align the Support Plates, The Shackle Cross Members and the Cross Member Support when moving the assembled FH1 bracket.
- Page 3 Flyware Bracket System Step 3 Attaching Brackets to Enclosures. Secure the assembled FH1 bracket to the tops of the neighboring enclosures using the four bolts provided. Tighten bolts in an alternating, diagonal pattern. Tightening each bolt gradually until all are firmly secured.
-
Page 4: Dispositions Circulaires Suspendues
à des points stratégiques sur le dessus et au- dessous de l’enceintes. Dispositions Circulaires Suspendues Un kit FH1 permet le montage d’une paire d’enceintes en disposition circulaire serré avec écartement optimum. Des enceintes additionnelles peuvent êtres ajoutés pour obtenir des regroupements plus grands (3 enceintes ou plus). - Page 5 “Shackle Cross Members” et des supports “Cross Member.” Conseil : il est plus facile d’assembler le support FH1 à l’écart de l’enceinte, soit sur une table ou sur le dessus de l’enceinte. Utiliser les boulons fournis pour aligner les plaques de support, les “ Shackle Cross Members”...
- Page 6 (ex. Marque Locktite™, Permabond™, ou Sur-Lok™). Cela aidera à garder les boulons solidement en place. Après avoir installé le support FH1 du dessus sur les enceintes, coucher les cabi- nets sur le dos pour accéder au-dessous. En utilisant les plaques de support, les boulonner fermement ensemble en formant la même disposition diagonale utilisée...