The Fountainhead Group 183435 Manuel D'utilisation Et D'entretien page 9

SPRAYER MAINTENANCE
Cleaning & Storage
WARNING: RISK OF PERSONAL INJURY DUE TO CHEMICAL EXPOSURE. Always wear appropriate
personal protection equipment as instructed by chemical manufacturer when using, preparing,
handling, spraying, or disposing of chemicals. This includes at least goggles, gloves, and protec-
tive clothing. Prior to performing maintenance always depressurize Sprayer by setting Power
Switch to the OFF (O) position and then opening the Shut-off (depressing the Lever) to spray until
liquid flow stops.
CAUTION: RISK OF DAMAGE TO INTERNAL COMPONENTS. Failure to properly rinse out the Sprayer
may allow chemical residue build-up that can clog or damage the Filters, Pump, Shut-off, Wand,
and Nozzle. Chemical residue build-up can also contaminate subsequent applications. Leaving
chemical liquids in the Sprayer when not in use can lead to premature Sprayer wear. Never store
Sprayer with chemical in any part of the Sprayer.
1. Set the Power Switch to the OFF (O) position.
2. Remove the Battery. See Removing the Battery.
3. Empty any extra chemical from the Tank into a suitable container for later use or disposal according to
chemical manufacturer's instructions.
4. Use clean water to thoroughly rinse and empty the Tank until all chemical and residues are removed.
5. Add approximately 1 quart [1 liter] of clean water to the Tank.
6. Insert the Battery. See Inserting the Battery.
7. Set the Power Switch to the ON (I) position.
8. With clean water in the clean Tank, spray water through the Pump, Hose, Shutoff, Wand, and Nozzle
for at least 30 seconds to rinse them out. Failure to rinse out Pump, Hose, Shutoff, Wand, and Nozzle
may allow chemical residue build-up that can clog or damage the components. After heavy use rins-
ing the Nozzle may not be enough to remove residue. The Nozzle may need to be cleaned with a
small brush.
9. Empty out any remaining water from the Tank then continue to spray until water no longer comes out
the Nozzle. This indicates that most of the water in the system has been removed.
10.Set the Power Switch to the OFF (O) position.
11.Remove the Battery.
12.Open the Shut-off (depress Lever) to release any remaining pressure in the Hose.
13.Allow the Sprayer to dry. This is best done by removing the Cap and Strainer Basket and hanging the
Sprayer upside down to let it drain.
14.Once the Sprayer is dried, turn the Sprayer upright and reinstall the Strainer Basket and Cap to pre-
vent debris from entering the Tank.
15.Store the Sprayer and Battery indoors in a warm, dry location out of direct Sunlight and away from
any sources of moisture or intense heat. Do not store Sprayer where freezing temperatures (below
32°F/0°C) will occur. Allowing water to freeze inside the Sprayer may cause damage to the Pump,
Seals, Shut-off, or other components, and void the Sprayer warranty.
16.To ensure optimal Battery life the Battery should be charged at least once every 3 months when not
in use. See Charging the Battery.
Servicing the In-Tank Filter:
CAUTION: RISK OF DAMAGE TO INTERNAL COMPONENTS. Do not operate the Sprayer without the
In-Tank Filter properly installed. Doing so could allow debris to enter the Pump causing clogging
or damage to the Pump.
1. Ensure the Power Switch is in the OFF (O) position.
2. Remove the Battery from the Battery Compartment. See Removing the Battery.
3. Remove the Tank Cap and Strainer Basket. Rinse with clean water to remove any debris. Place the
Strainer Basket and Cap on a clean surface where they will not collect dirt, dust, grass clippings, or
other debris.
4. Pour any liquid from the Tank into an appropriate container for later use or proper disposal according
to chemical manufacturer's instructions.
5. Rinse and empty the Tank to remove any dirt, debris, or residue.
SPRAYER MAINTENANCE
page 9