Publicité
Les langues disponibles
Les langues disponibles
0
TRI
SYS sarl –
300 Rue des Arts et Métiers, 21410 PONT DE PANY
2
Installation and operating manual
Modular 2 channels switch receiver for LED
lighting
Ref. 10020107
1. General
1.1 Use
1.2 Guarantee terms
This operating manual is an integral part of the device and our guarantee terms. It must always
be delivered to the user. We reserve the right to modify the technical design of these devices
0
without warning. TRI
SYS products are manufactured and their quality checked by making
2
use of the latest technologies and taking into account the applicable national and international
directives. If nevertheless a fault arises, TRI
follows, without prejudicing the rights of the end customer that arise from the sales contract
with his reseller:
If the event of exercising of a legitimate and regular right, TRI
rectify the device fault or supply a fault-free device. Any claim beyond this and all claims for
consequential damages are excluded.
A legitimate fault exists if the device cannot be used at the time of delivery to the end customer
because of a design or manufacturing defect or if its practical use is severely limited. The
guarantee is void in cases of natural wear and tear, incorrect use, incorrect connection, where
the device has been repaired or external influence. The guarantee period is 24 months (from
the date of invoicing). French law applies to the regulation of guarantee rights.
2. Safety
WARNI
WARNING! Risk of electric shocks! (See UTE C18-150) The device contains
live internal components. Risk of wounds or injuries if contact occurs! All work
on the mains supply network and the device must only be carried out by
authorised professional technicians.
• Before carrying out any work, switch-off and isolate the device.
• Secure the device to prevent it being switched back on.
• Check the device is in a zero-volts state.
• Carefully reclose the casing before reconnecting to mains power.
Observe the following points:
• The laws, standards and directives in force.
• The device operating manual and best practice at the time of installation.
• An operating manual can only give general instructions. They must be interpreted in the
context of a specific installation.
The device is intended solely for use conforming to its purpose. Any repairs or modifications
by the user are forbidden! Do not use with other devices the operation of which could endanger
people, animals or property.
3. Technical characteristics
General characteristics
Transmission frequency band
Transmit power
Power supply
Terminal capacity
-2-
Output (zero potential)
2 contacts micro distance (µ) opening
contacts, I
=100mA
min
Category receiver
Power measurement accuracy
Number of modules
Mounting type
Consumed power
Ambient temperature
Storage temperature
Ambient humidity
Degree of protection
Installation altitude
-1-
The output voltage of the 2 channels receiver is the same as the supply voltage.
-2-
Consult us for other types of charges.
-3-
For powers greater than 10W.
-4-
Power consumed without activation of the relays.
TOC2003NUaa_0620
EN
The modular 2 channels switch receiver
10020107 is used to receive radio signals from switch
0
transmitters or
LINE sensors (see compatibility
2
table §6.1). Designed for switching LED and compact
fluorescent lighting loads, it can also switch resistive
loads (halogen), fluorescent tubes, TBT halogen
lamps with ferromagnetic and electronic transformer,
power contactors or small motors.
The 2 channels switch receiver is equipped with the
« repeater » function as well as the « consumption
indicator » function (see §5.3 and §6.4).
Before use, the transmitters must be assigned to a
receiver. Each sensor or transmitter can control an
unlimited number of receivers.
Note: Read the user manual carefully before
commissioning.
To
consult
the
indications, it is recommended to connect the 2
channels switch receiver 10020107 with a suitable
software.
0
SYS undertakes to remedy the default as
2
0
SYS, may at its sole discretion,
2
868.0 MHZ à 868.6 MHZ
+10 dBm
-1-
110 - 230V
230V
/ 50 Hz
2
2
1x1,5
to 2,5
max rigid
max µ2x2A/2x345VA resistive (cos φ=1)
LED: 2x170W
Compact fluorescent: 2x170W
Halogen: 2x460W
Inductive: 2x400W (cos φ= 0,4 à 0,6)
2
-3-
1% +/- 1 digits
1 module of 17.5 mm
DIN rail mounting
-4-
< 0.35 W
from -10°C to +45°C
from -20°C to +80°C
from 0 to 75%hr
(without condensation)
IP20 with plastron
2000m max.
Range in buildings
Masonry
Reinforced concrete
Plasterboard / wood
Note: The signal strength between the transmitter and the receiver decreases as the distance
increases. Where there is a line of sight connection, the range is approximately 30m in corridors
0
and 100 m in large workshops or halls. The range can be increased with an
LINE
2
Respect a minimum range of 10 cm between transmitter and receiver.
4. Installation and initial use
4.1 Safety instructions
The installation and initial use must only be performed by authorised qualified electricians. The
electrical installation must be placed off-load before connection it to the mains (230V~/50Hz).
Conform to the legislation and standards in force in the country of use.
4.2 Installation
•
This product is designed for indoor use. It is maintenance free.
• This product is intended for installation only on horizontal DIN rail, in an electrical panel
(mounted on a vertical wall) with compulsory installation of a plastron which will be connected
to the ground of the installation if it is metallic.
consumption
• For compliance with the standard reference, height of the plastron (compared to the above
DIN rail) must not exceed 48 mm with a minimum thickness of 1 mm.
• NEVER install the receiver in a metal casing or in the immediate vicinity of large metallic
objects.
• Installation on the ground or close to the ground is not recommended. Thank you to refer to
the installation standards of each country.
• Protect the supply line with a circuit breaker 4A curve C adapted to the installation.
Connection principle diagram:
4.3 Description of the connection
- Description of the 2 channels receiver connection:
7mm
4.4 Initial use
• Connect power to the electrical installation after it has been installed.
• Program the transmitter on the receiver (see § 5).
20m, through 3 walls at most
10m, through 1 wall/ceiling at most
30m, through 5 walls at most
Schematic diagram of electrical
connection to lighting loads.
They can be replaced by other
types of loads (see table §3).
0
.
LINE repeater
2
4/6
Publicité
