Unpacking Instructions; Connection To The Mains - Tecfrigo GIROTONDO XW90 Mode D'emploi

Operator's guide:

1)Unpacking instructions

2)Opening the protective cover
3)Cleaning the internal basin
I
4)Cleaning the cover and external parts

5)Connection to the mains

UK
6)Controls
7)Checking correct operation
D
8)Internal and evaporator cleaning
E
F
WARNINGS
!
NL
It is most important that this instruction booklet is kept together with the appliance both for future
reference and for reasons of safety.
P
1. Adults should operate this appliance only. Do not allow children to use the controls or play with it. 2
is forbidden to modify in any way the main functions and characteristics of this appliance. . The electrical
S
installation of the appliance should be carried out by a qualified electrician or other competent person.
4 . Never attempt to carry out repairs unassisted. Inexpert repairs can cause serious damage and
malfunction. . Assistance has to be provided by an authorized engineer only. Always use original spare
DK
parts. . This appliance is not suitable for the storage of basic commodities not including food-stuffs. 6
7 . The manufacturers of this appliance accept no responsibility for the consequences of misuse in
FIN
contravention of these safety instructions. It further reserves the right to carry out improvements without
prior notice. 8
B
sources of heat (such as radiators, stoves, etc) and drafts (such as windows, doors, ventilation systems,
air conditioning, etc ...).
GR
air or products to be refrigerated should cause ice to form on the evaporator, we recommend stopping the
compressor and placing the goods in special refrigerated containers, kept at the same temperature, until
CZ
defrosting is completed;if this is not carried out the compressor will continue to operate leading to a
wasteful consumption of electricity and poor performance.
EE
Our products are for internal use only do not install outside restaurants, shops.
!
LV
LT
1. UNPACKING INSTRUCTIONS
CARDBOARD BOXES 1a.
H
WOODEN CRATE 1b.
between the appliance and pallet or crate.
M
the appliance on a flat, level surface.
it. . Sort out the packaging materials in order to facilitate disposal. . The appliance can be locked in 7
PL place by engaging the wheel brakes.
2. OPENING THE PROTECTIVE COVER
SK
1. Plug the machine into the power supply socket, as described in Chapter 7.
electric lifting system (A) to position II until the cover is fully (see fig. 2).
SLO
3. CLEANING THE INTERNAL BASIN
1
. Remove the protection film from the stainless steel parts. . Clean the basin with a soft sponge and
neutral detergents.
4. CLEANING THE COVER AND EXTERNAL PARTS
1. Never use detergents containing alcohol or solvents which would irremediably damage the cover,
compromising its transparency. . Use only a soft damp sponge. . As far as the wooden surfaces are
concerned, use proprietary detergents especially designed for wooden surfaces, which are water-based
and do not contain solvents. . Dry with a clean cloth.
5. CONNECTION TO THE MAINS
1 . Ensure that mains voltage and frequency are the same as those stated on the rating plate (A) attached
to the appliance. . Ensure that the supply socket:
rated current as set out on the rating plate;
switch with In = rated value as stated on the rating plate; - differential with Id sensitivity = 30 mA.
Ensure that there is no danger of explosion (AD) in the room. . Make sure the environment is suitable for
the power supply cable provided. The cable of the appliance is H05 VVF, designed for internal use.
5 . Insert the plug in the socket (do not use three-way adapters and reduction adapters).
equipment has been transported or stored overturned, let is rest in its correct position for at least 3 hours
before hooking it up to the mains (see fig. 5).
5
. Avoid installing the cabinet directly in line with sunlight. .
10 . Keep the ventilation grills free from obstruction for at least 30 cm.
Cut surrounding tape. Remove the cardboard package by sliding it upwards.
Remove the nails from the wooden crate with care. . Insert forks of forklift truck
6.
2
4
2
Operator's guide
Maintenance manual (Page 18):
1)Cleaning the condenser
2)Access to the motor compartment
3)Replacement of the cover's lifting motor
4)Wiring diagram diagram of refrigeration unit
3. 4.
Lift the appliance.
Make sure there is nothing left in the package before disposing of
2
3
a) is properly earthed;
c) complies with the IEC regulations:- thermal-magnetic
4
6
3
9 Never install the appliance near
2
Remove the pallet or crate. . Place
8
2 . Turn the switch of the
b) fulfils the requirements of the
N.B.:
. It
11 . If damp
5
3 .
if the