Time Zone And Daylight Saving Time (Dst) Setting - La Crosse Technology WS-8025SU Mode D'emploi

OK Oklahoma TX
17K Boise City DFW
LAW Lawton ELP
OKC Oklahoma City HOU
TUL Tulsa LRD
OR Oregon ODO
BNO Burns SAT
EUG Eugene UT
MFR Medford SAL
PDX Portland SGU
SLE Salem SLC
PA Pennsylvania TSN
CXY Harrisburg VA
PHL Philadelphia DON
PIT Pittsburgh LYH
SCR Scranton ORF
PR Puerto Rico RIC
SJU San Juan ROA
RI Rhode Island VT
PVD Providence BTV
SC South Carolina MPR
CHS Charleston WA
CUB Columbia ABE
GMU Greenville ALW
SD South Dakota KTF
FSD Sioux Falls MVN
PIR Pierre OLM
RAP Rapid City SEA
TN Tennessee SFF
BNA Nashville TON
CHA Chattanooga YKM
DKX Knoxville WI
MEM Memphis AUW
TX Texas GRB
ABI Abilene LSE
AMA Amarillo MSN
AUS Austin MWC
BRO Brownsville SSQ
GB
P.10
Texas (cont.) WV West Virginia
Dallas/Ft. Worth CRW Charleston
El Paso HLG Wheeling
Houston WY Wyoming
Laredo BYG Buffalo
Odessa CPR Casper
San Antonio CYS Cheyenne
Utah LAA Little America
Saline WYE West Yellowstone
St. George
Salt Lake City
Thompson
Virginia
Vienna
Lynchburg
Norfolk
Richmond
Roanoke
Vermont
Burlington
Montpelier
Washington
Aberdeen
Walla Walla
Kettle Falls
Mt. Vernon
Olympia
Seattle
Spokane
Tonasket
Yakima
Wisconsin
Wausau
Green Bay
La Crosse
Madison
Milwaukee
Spooner
Canada City Listing
Code City Code
EDM Edmonton YEL
ALB Calgary OTT
VAN Vancouver SUD
WIN Winnipeg THU
FRE Fredericton TOR
HAL Halifax
Mexico City Listings
Code City Code
CHH Chihuahua MEX
DUR Durango GUA
E. Time Zone and Daylight Saving Time Settings
1. Press and hold the " SET " button for 1 second.
2. Press and release the " SET " button 9 times.
3. The time zone will now flash based on the city selected.
4. Press and release the "+"or "-" button to adjust to the correct time zone.
5. Press and release the " SET " button to advance to the Daylight Saving Time setting.
6. "dst ON" will now flash.
7. Press and release the "+" or "-" button to select DST 1 (recognizes Daylight Saving
Time change) or DST 0 (does not change with Daylight Saving Time).
Note : Some locations (Arizona and parts of Indiana) do not follow Daylight Saving Time.
8. Press and release the " SET " button to advance to the weather measurement units
settings (skip steps 1 and 2 in section E if continuing).
F. Weather measurement units (˚F/˚C, inHg/hPa)
1. Press and hold the " SET " button for 1 second.
2. Press and release the " SET " button 11 times.
3. The selected temperature units will now flash (˚F default/factory setting).
4. Press and release the "+"or "-" button to select ˚F (Fahrenheit) or ˚C (Celsius).
5. Press and release the " SET " button to advance to the barometric air pressure units
setting.
6. The selected air pressure units will now flash (inHg default/factory setting).
7. Press and release the "+"or "-" button to select inHg (inches of Mercury) or hPa
(hectopascal or millibars).
8. Press and release the " SET " button to advance to the barometric air pressure calibration
setting.
9. The air pressure reading will now flash (29.91 inHg, 1012.8 hPa as default).
10. Press and release the "+"or "-" button to adjust to the correct relative air pressure
based on local reports.
11. Press and release the " SET " button to advance to the forecast sensitivity setting.
Note : Barometric air pressure is usually reported as "relative air pressure". This reading is
based on the combination of absolute air pressure and altitude. In general, an increase in
altitude will result in a decrease in air pressure. Relative air pressure will make readings in
nearby locations relative to each other to allow for proper forecasting. The absolute air
pressure reading in the Weather Center cannot be calibrated, only the relative air pressure.
City Code City
Yellowknife CHT Charlotte Town
Ottawa MON Montreal
Sudbury QUE Quebec
Thunder Bay REG Regina
Toronto WHI Whitehorse
City Code City
Mexico City HER Hermosillo
Guadalupe
P.11
GB