Publicité
Les langues disponibles
Les langues disponibles
1
3
4
2
5
6
1. Transport handle.
2. Suction hose.
3. Return hose.
4. On/off switch.
5. Inlet filter.
6. Pressure regulator.
7. Prime/spray selector.
8. Airless gun.
9. Airless hose.
10. Hose connection.
USE INSTRUCTIONS.
►
Before starting up the airless electric equipment,
we recommend that you carefully read all of the
instructions as indicated
regulations regarding the prevention of accidents,
health and safety directives, laws and applicable
restrictions for work places
equipment must only be used by persons who have
been instructed in its use and only for the purposes
for which it has been designed.
POWER SUPPLY.
►
Make sure the power supply is adapted to the
requirements shown on the information panel of the
airless electric equipment (1)
low voltage will make it operate slowly
reduce performance and may cause the motor to
overheat.
EXTENSION CORD.
►
If the working area is at some distance from the
power supply, use an extension cord of enough
diameter and quality.
EARTH CONNECTION.
►
The airless electric equipment must be
connected to earth while being used to protect the
operator from possible electrical shocks.
7
►
Please respect all
►
The airless electric
►
Using the motor at
►
This will
PRIME/SPRAY
►
This switch toggles the unit between the
"priming" and "spraying" mode (2).
NOZZLE.
►
The nozzle is reversible and removable to make
cleaning and unclogging easier
position to use the airless gun (3)
8
opposed position to clean the nozzle (4).
PRESSURE CONTROL KNOB.
►
The pressure control knob can be adjusted for
9
high pressure spraying, low pressure spraying,
priming/cleaning and rolling (5).
INSTALATION.
►
Remove or cover objects that you want to
protect from overspray (paint mist)
hose to paint hose outlet and tighten with wrench
►
(6)
Attach paint hose to airless gun and tighten
with two wrenches (7)
knob to "low pressure spray" setting (8).
RELIEVE PRESSURE.
Turn power switch "off" and unplug unit from
►
►
outlet (9)
mode to safely release most pressure (10)
airless gun into paint pail and activate the airless
gun trigger to relieve an remaining pressure (11)
Note: Always set to "prime" mode between uses.
►
PRIME AIRLESS GUN.
►
This procedure is used for first time operation
and also to flush storage fluids out of the airless
►
gun
For oil-based paint, flush with mineral
spirits followed by warm clean water
to prevent fire: When using mineral spirits, ground
airless gun by holding it against a metal container
while flushing
flush with warm clean water.
PRIME AND STARTUP.
►
Separate smaller priming tube from suction
►
tube (12)
►
(13)
Submerge suction tube in water or flushing
solvent (14)
mode (10)
"prime/clean" setting (15)
turn "on" power (16)
and water or flushing solvent as well as air
bubbles will be purged from system
discharge from priming tube into waste bucket
for 30 to 60 seconds then switch power to "off"
►
(9)
Remove suction tube from water or flushing
solvent and submerge in paint pail (17)
power to "on" (16)
English
5
►
►
Turn pressure control
Turn "prime/spray" switch to "prime"
►
For water-based (latex) paint,
Place priming tube in waste bucket
Turn "prime/spray" switch to "prime"
►
►
Adjust pressure control knob to
►
Plug in the unit and
►
The unit will start pumping
►
Paint should work itself from
Turn to "spray"
►
Turn to the
►
Attach paint
►
Point
►
Warning!
►
Let fluids
►
Switch
Publicité
