KIKKA BOO FELIX Mode D'emploi page 11

2.4. THE HEADREST HEIGHT ADJUSTED METHOD
Depending to the height of the child, the headrest can be adjusted in 11 positions. As shown, adjust the red handle to the appropriate height by
adjusting the handle up and down at the same time.
Important: after releasing the headrest by adjusting the lever, check that the headrest is locked in a safe and suitable position by pulling up or down the
head.
2.5. THE SHOULDER STRAPS ADJUSTED METHOD
Check that the shoulder strap height is suitable for your child: straps should pass through straps that are equal to the child' s shoulder or slightly higher
than the child's shoulder position (the correct seat belt position is shown in the gure).
The height of the shoulder strap of this product can be adjusted up and down with the up and down of the headrest. When using, adjust the height of
the headrest to adjust the suitable shoulder strap height.
2.6. THE BUCKLE USED METHOD
2.6. Pull the button left and right together.
2.7. Insert the closed insert into the slot at the same time. If you hear the H clickn sound, it means that the buckle is stuck. Pull the insert up and check
that the buckle is locked properly.
2.8. To unfasten the seat belt, press the red button down and the insert will pop up automatically. THE LENGTH OF THE SHOULDER STRAPS ADJUSTED
METHOD
2.9. Tighten the straps:
Pull the straps outward until the straps are completely tightened. Tighten the straps as much as possible without causing discomfort to the
child. The leg seat belt is as low as possible and should be located near the crotch rather than the abdomen. Loose straps are dangerous. So
every time the child is placed in the child' s seat, check that the seat belt adjuster can be used normally, and then pull the 5 straps, tighten
the straps, and do not twist the straps.
2.10. Loosen the straps:
The shoulder strap can be loosened by pressing the seat belt adjuster (hidden under the cover of the seat).
Action: press the seatbelt regulator down while the other hand holds two straps to the front of the child to loosen the straps.
2.11.THE ISOFIX ADJUSTED METHOD
As shown press the red ISOFIX release button and push the FIT chuck out to the outermost so that the ISOFIX chuck can be installed.
If you want to retract the ISOFIX chuck, you can pull the ISOFIX chuck back by pressing the red ISOFIX release button inward.
2.12. ISOFIX INSTALLATION
Step 1: First pull the ISOFIX chuck to the outermost end, then insert the ISOFIX interface on the car. When you hear "click" to indicate that the
ISOFIX chuck and the ISOFIX interface are fully docked, note: at this time, the FIT lock display window appears green.
Step 2: Push the seat against the back of the car until the two are perfectly tightly aligned. If you want to release the ISOFIX chuck, you can
unlock the ISOFIX chuck by pressing the red release button of the FIT chuck.
2.13. RECLINING ANGLE ADJUSTING OF THE CHILD SEAT
As shown the seat angle can be adjusted by pressing the red angle adjusting handle. It is convenient to adjust the suitable angle and increase
comfort when using.
2.14. THE ROTATION OF THE RESTRAINT ADJUSTED METHOD
As shown the seat can be rotated 360 degrees by pressing the red rotary adjusting button down. It is convenient to adjust the suitable
direction and increase the usability when using.
III. INSTALLATION OF CHILD SEATS (GROUP O+ : 0-13KG) -OPTION 1 FOR CAR WITH ISOFIX
3.1. This product is suitable for children with weight in 0-13Kg, rearward installation.
Step 1: First adjust the seat to the most inclined gear, and thenrotate the seat body position 180 degrees on the car seat.
Step 2: Use ISOFIX to secure the seat to the car seat, make sure the ISO FIX lock display window appears green, and then slowly push the seat
onto the back of the car seat until completely tted.
Step 3: The top strap of the seat is hung through the middle of the head of the car seat to the corresponding hook on the car (on the node
suggested in the automaker's manual). Tighten the tape of the top strap until the top strap regulator appears green, while ensuring that the
top strap is xed and tightened.
3.2.Installation of Child Seats (Group O+ : 0-13kg)-Option 2 for car without lso x
This restraint is suitable for children with weight 0-13kg, rearward facing installation .
Step 1: Adjust the seat to the fully reclined and then rotate the seat body 180 degrees.
Step 2: Place the child seat centrally onto the passenger seat and the front of the child seat must be pushed rmly against the back of the
vehicle seat .
Step 3: Pull o approximately a meter of lap and diagonal belt and diagonal belt and route the two belts as follows:
Diagonal section : Pull the diagonal section through the slot at top of the seat backrest and wrap it around the back of the seat.
Lap section : rst release the buck and get o the cushion, then thread the lap section through the child seat, pay attention the lap belt not
to interfere the child seat belts.
ENGLISH