steute RF I/O SW868-4E-2,2Ah Instructions De Montage page 3

RF I/O SW868/SW915/SW917/SW922-4E-2,2Ah
//
Montage- und Anschlussanleitung / Funk-Universalsender
Mounting and wiring instructions / Wireless universal transmitter
Instructions de montage et de câblage / Emetteur universel sans fil
Istruzioni di montaggio e collegamento / Trasmettitore universale wireless
Instruções de montagem e instalação / Transmissor universal sem fio
Инструкция по монтажу и подключению / Универсальный радио-передатчик
English
Connectable devices:
Device
0.3 m
RF IS M8 nb-ST
RF IS M12 nb-ST
RF IS M18 nb-ST
RF IS M30 nb-ST
RF RC 20 1S-ST 1335490
connecting cable,
open wire ends
Note:
- External switches (devices) must be suitable for the specified switch-
ing capacity (3 V DC/0.3 mA at the moment of switch-on). The switch-
ing capacity ensures a long battery life. Switches with gold contacts
and reed switches are suitable.
- Always use the specified connecting cable to connect external devic-
es. Only suitable for load-free external devices.
- In the event of a short circuit using the connecting cable 1215497, the
battery will discharge.
In this case: Replace the battery.
Design of wireless range
The radio signal is attenuated on the way from the transmitter to
the receiver. In addition, the radio signal is attenuated/influenced by
obstacles. The degree of attenuation depends on the material of the
obstacle. The following tables serve as a guide.
Penetration of radio signals:
Material
wood, gypsum, glas uncoated
brick stone, press boards
armoured concrete
metal, aluminium lamination, water
Typical ranges:
Place of use
in free field (SW868/915/917)
in free field (SW922)
indoors (SW868/915/917)
indoors (SW922)
Material No. (Cable length)
0.5 m 1 m 2 m
1470040 1373082 1305745
1228522 1356467 1189974
1261564 on request 1189975
1260490 1228548 1189976
1215497
Penetration
90...100%
65...95%
10...90%
0...10%
Wireless range
(approx.)
450 m
150 m
40 m
20 m
Field strength meter for range test:
Transmitter Device
SW868 swView 868 MHz
SW915 swView 915 MHz
SW917/SW922
Radio operation
The transmission of a switching command from the transmitter to the
receiver takes about 80 to 100 ms, based on the sWave® data trans-
mission. The switching signal of a transmitter must not be generated
at a shorter distance, otherwise this signal will be overlooked. The re-
ceiver must support the sWave® protocol of the steute modules. Each
switching operation triggers a transmission from the radio unit. This
also applies if several channels are activated or deactivated simulta-
neously. The current value of the battery voltage is transmitted with
each transmission.
Allocation of locations and radio frequencies:
Device type Radio frequency
SW868 868.3 MHz
SW915 915.0 MHz
SW917 917.0 MHz
SW922 916.5 MHz
Battery
Variants with battery included in delivery:
Name
RF I/O SW868-4E-2,2Ah
RF I/O SW868-4E-2,2Ah RS Components
RF I/O SW915-4E-2,2Ah
The delivery includes a lithium battery SL-760/S 3.6 V/2.2 Ah (AA).
To replace the battery: see section »Battery replacement«.
Variants without battery included in delivery:
Name
RF I/O SW915-4E-w/o
RF I/O SW922-4E-w/o BATT LBT
RF I/O SW917-4E-w/o
To insert the battery: see section »Battery replacement«.
Spare part:
Name
Lithium battery SL-760 (3.6 V/2.2 Ah AA)
3 / 20
Material No.
1190393
1221794
on request
Place of use according to
EU 2014/53/EU (RED)
USA FCC
Canada IC
Mexico IFT
Brazil ANATEL
Japan ARIB STD-T108
Material No.
1359762
1459212
1362074
Material No.
1432305
1423394
1284629
Material No.
1351045