Publicité
Les langues disponibles
Les langues disponibles
6.
Your desktop may or may not be pre-drilled. Check both sides of the desktop
before placing the table frame on the underside of the desktop.
Adjust the width of the tableframe to fit the desktop by sliding the two halves
outward. We recommend letting at least 1/2" of the desktop protrude beyond
the frame width (on each side) and centering the Side Brackets
this position.
7.
If the desktop is pre-drilled, perform Step 8 before Step 7.
If the desktop is not pre-drilled, secure the position of the Center Rails
(part 4)
Rails
8.
won't pierce the surface when screwed all the way in.
desktop if your desktop is not pre-drilled. Never use countersunk screws.
Double-check that the desk frame is properly positioned on the underside
of the desktop. Attach the desk frame to the underside of the desktop using
seven (7) M5 x 20 Wood Screws
that the front of the handset is flush with the front desktop edge (or recessed
up to 1/8"). The handset may be placed anywhere along the front edge of the
desktop but we recommend placing it towards one end so it does not interfe-
re with your chair when seated. Use two (2) M5 x 16 Wood Screws
to attach the handset to the desktop.
to the components.
9.
Slide the Control Box
Connect the cable exiting the Leg
End-CB
Connect the Cable
(part 6)
Connect the Power Cord
sive-backed Cable Clips
12
(part 10)
using eight (8) M6 x 10 Machine Screws
.
(part 10)
Ensure that the M6 x 10 Machine Screws
contact the Center
(part 4)
(part 4)
by sliding the Center Rails
as needed.
Double-check that the wood screws are not too long for your desktop and
We recommend that you pre-drill all holes needed for fastening the
(part 12)
. Attach the Handset
Do not overtighten screws in this step. Overtightening can cause damage
(part 6)
(part 3a)
onto the Frame End-CB
(part 1)
that is attached to the Frame
(part 3a)
(part 6).
directly into the Control Box
(part 9)
(part 1)
to the other Leg
and to the Control Box
(part 7)
. Connect the Handset
cable to the Control Box
(part 8)
(part 6)
to the Control Box
. Use the adhe-
(part 14)
to secure the cables so they do not sag.
ENGLISH
ENGLISH
10.
Turn the assembled desk right-side up. With at least two people, grab the DESK FRAME (not the desktop) and turn the desk
right-side up. Adjust the pre-installed glides on the Feet
(part 8)
11.
Plug the Power Cord
(part 5)
in
USE
!
Make sure no obstacles are in the desk's path when adjusting its height.
Make sure the desktop is not touching any walls.
Make sure all cords have the appropriate length to accommodate the change in height.
IMPORTANT: You must RESET the desk prior to use.
RESET PROCEDURE: Press and hold the DOWN button on the Handset
height. Release the DOWN button. Press and hold the DOWN button again until the LED display reads „RST" or about 10
seconds on non-LED handset models. Release the DOWN button. Press and hold the DOWN button again until the desk
sinks a little bit more, slightly rises and stops. Release the DOWN button. Your desk is now ready to use.
To program up to four presets (on some models): Use the up/down buttons to find a desired height, then press „M" followed
by a number 1-4.
CAUTION: Once a preset button is pushed, the desk will move to the programmed height (see caution box above).
(part 7)
so
TROUBLE SHOOTING
(part 13)
If your desk is not functioning properly it may need to be reset. Follow the RESET procedure outlined in the USE section. If your
desk has a handset with an LED readout and it displays „RST" (reset), perform the reset procedure outlined in the USE section.
If the LED readout displays an error message („Er1" - „Er13 „) confirm that all wired connections are secure (legs to cables,
cables to control box). Then perform the reset procedure outlined in the USE section. If the error message persists after the reset
procedure, contact your seller. If the height between the legs exceeds 1.5 inches, stop the reset procedure & contact your seller.
If the handset displays „HOT", let the base cool down for 20 minutes.
.
SPECIFICATIONS
(part 6)
.
(part 2)
as needed.
into a 110v outlet.
(part 7)
until the desk reaches the lowest possible
Heiqht Range
595 mm - 1245 mm (without desktop)
Base Width
1080 mm min. - 1800 mm max.
Travel Speed
32 mm / s
Load Capacity
1200N
Duty Cycle
10%. Max. 2 mins on, 18 mins off
Soft start/stop
Adiustable levelina studs
4 Memory presets (some models)
13
Publicité
