Publicité
Les langues disponibles
Les langues disponibles
GENERAL
OPERATION
Power Supply Capacity
Make sure the power supply can supply enough
rated and peak watts for the items being powered
at the same time.
1. Select the items to be powered at the same time.
2. Total the rated watts of these items. This is the
amount of power the power supply must produce
to keep the items running. See wattage reference
chart.
3. Estimate how many peak watts will be needed.
Peak wattage is the short burst of power needed to
start electric motor-driven tools such as a circular
saw. Because not all motors start at the same time,
total peak watts can be estimated by adding only
the item with the highest additional peak watts to
the total rated watts from step 2.
Application/
Equipment
Job Site
Electric Drill - 3/8"
Work Light
Reciprocating Saw
Circular Saw - 7-1/4"
Miter Saw - 10"
Air Compressor 1/4 HP
Airless Sprayer 1/3 HP
Radio
M18™/M12™
Standard Charger
(48-59-1812)
M18™/M12™
Rapid Charger
(48-59-1808)
Lifestyle
Microwave
TV
Satellite Receiver
Portable Fan
Heater
String Lights
Laptop
Tablet
Cellphone
*Wattages listed are approximate.
Check tool or appliance for actual wattage.
Estimated
Estimated
Rated
Peak
Watts*
Watts*
600
1000
1000
1000
960
1920
1400
2300
1800
2800
970
1600
600
1200
50
50
60
60
75 (M12™)
75 (M12™)
120 (M18™)
120 (M18™)
1000
1000
50-300
50-300
250
250
40
120
1300
1300
50-150
50-150
50-150
50-150
15
15
5
5
Fuel Gauge
Use the Fuel Gauge to deter
mine the battery pack's re-
maining run time. Press the
Fuel Gauge button to dis-
play the lights. The Fuel
Gauge will light up for 2-3
seconds. When less than
10% of charge is left, 1 light
on the Fuel Gauge will flash
slowly.
NOTE: If the Fuel Gauge doesn't appear to be
working, place the battery pack on the charger and
charge as needed.
Compared to NiCd battery pack types, MILWAUKEE
Li-Ion battery packs deliver fade-free power for their
entire run time. The tool will not experience a slow,
gradual loss of power as you work. To signal the end
of discharge, 1 light on the Fuel Gauge will flash
quickly for 2-3 seconds and the tool will not run.
Charge the battery pack.
NOTE: Immediately after using the battery pack,
the Fuel Gauge may display a lower charge than it
will if checked a few minutes later. The battery cells
"recover" some of their charge after resting.
Fuel Gauge
Lights
Diagnosis
Lights 1 - 4
Remaining
Solid
run time
Less than
1 Light,
10% run time
flashing slowly
left
1 Light,
End of
flashing quickly
discharge
Lights 1-4,
Current draw
flashing quickly
too high
Lights 1&3 /
Battery
2&4, flashing
temperature
alternatingly
too high
Using the Power Supply
This power supply converts DC electricity to 120 VAC
household power and/or USB charging power, allow-
ing the user to charge and power a variety of devices.
• To prolong the life of the power supply and attached
devices, it is important to take care when adding
electrical loads to the power supply.
• There should be nothing connected to the power
supply outlets before starting the power source.
• The correct and safe way to manage power supply
power is to sequentially add loads.
NOTE: The AC Outlet and USB ports can be used
at the same time. The internal fan may activate
during use.
1. Insert (4) required M18™ battery packs.
2. Press the power
supply ON.
3. Plug in and turn on the first load, preferably the
largest load. Permit the power supply output to
stabilize.
4. Plug in and turn on the next load. Again, permit
the power supply to stabilize.
NOTE: An alert will sound when the battery packs
are low.
5. When finished, turn off the power supply, discon-
nect the devices, and remove the battery packs.
7
Approximate Run
Time Remaining
78-100
%
55-77
%
33-54
%
10-32
%
Less than 10% if
bottom light is flashing
Solution
Continue working
Prepare to charge
pack
Charge pack
Reduce loading
on the power
supply, then retry.
Allow batteries to
cool, then retry.
button to turn the power
Publicité
