Français - Bosch GWS 880 Professional Notice Originale

pressure on the cutting disc and do not tilt or swing the
power tool.
Do not attempt to reduce the speed of a cutting disc coming
to a stop by applying pressure from the side.
Cutting Stone
Provide sufficient dust extraction when cutting stone.
u
Wear a dust mask.
u
The power tool may be used only for dry cutting/grind-
u
ing.
For cutting stone, it is best to use a diamond cutting disc.
When cutting especially hard materials such as concrete
with a high pebble content, the diamond cutting disc can
overheat and become damaged as a result. This is clearly in-
dicated by circular sparking, rotating with the diamond cut-
ting disc.
If this happens, stop cutting and allow the diamond cutting
disc to cool down by running the power tool for a short time
at maximum speed with no load.
If work is noticeably slower and circular sparking is present,
this indicates that the diamond cutting disc has become
blunt. You can resharpen the disc by briefly cutting into ab-
rasive material (e.g. lime-sand brick).
Information on structural design
Slots in load-bearing walls are subject to DIN 1053 part 1 or
country-specific regulations. These regulations must be ob-
served under all circumstances. Seek advice from the re-
sponsible structural engineer, architect or construction su-
pervisor before starting work.
Maintenance and Service
Maintenance and cleaning
Pull the plug out of the socket before carrying out any
u
work on the power tool.
To ensure safe and efficient operation, always keep
u
the power tool and the ventilation slots clean.
In extreme conditions, always use a dust extractor if
u
possible. Blow out ventilation slots frequently and in-
stall a residual current device (RCD) upstream. When
machining metals, conductive dust can settle inside the
power tool, which can affect its protective insulation.
Store and handle the accessories carefully.
In order to avoid safety hazards, if the power supply cord
needs to be replaced, this must be done by Bosch or by an
Bosch Power Tools
The power tool must always
work in an up-grinding mo-
tion. Otherwise, there is a
risk that it will be pushed
uncontrolled out of the cut.
For best results when cut-
ting profiles and rectangular
tubing, start at the smallest
cross section.
after-sales service centre that is authorised to repair Bosch
power tools.
After-Sales Service and Application Service
Our after-sales service responds to your questions concern-
ing maintenance and repair of your product as well as spare
parts. You can find explosion drawings and information on
spare parts at: www.bosch-pt.com
The Bosch product use advice team will be happy to help you
with any questions about our products and their accessor-
ies.
In all correspondence and spare parts orders, please always
include the 10‑digit article number given on the nameplate
of the product.
Great Britain
Robert Bosch Ltd. (B.S.C.)
P.O. Box 98
Broadwater Park
North Orbital Road
Denham Uxbridge
UB 9 5HJ
At www.bosch-pt.co.uk you can order spare parts or arrange
the collection of a product in need of servicing or repair.
Tel. Service: (0344) 7360109
E-Mail: boschservicecentre@bosch.com
You can find further service addresses at:
www.bosch-pt.com/serviceaddresses
Disposal
The power tool, accessories and packaging should be re-
cycled in an environmentally friendly manner.
Do not dispose of power tools along with
household waste.
Only for EU countries:
According to the European Directive 2012/19/EU on Waste
Electrical and Electronic Equipment and its implementation
into national law, power tools that are no longer usable must
be collected separately and disposed of in an environment-
ally friendly manner.
Français
Consignes de sécurité
Avertissements de sécurité généraux pour l'outil
Lire tous les avertissements de sé-
AVERTISSE-
curité et toutes les instructions.
MENT
Ne pas suivre les avertissements et
instructions peut donner lieu à un choc électrique, un incen-
die et/ou une blessure sérieuse.
Français | 21
1 609 92A 3FT | (12.02.2021)