Legend Brands DRI-EAZ HEPA 700 Manuel Du Propriétaire page 2

HEPA 700 APPLICATIONS
•
Water Damage
•
Construction Dust Control
•
Mold Remediation
•
Odor control
•
Other uses: The HEPA 700 can be used for dust
abatement, fire damage remediation, jobsite ventilation,
and positive or negative air setups for contamination
cleanup and cleanroom environments. Use in homes,
businesses, institutions, schools, hospitals, long term care
facilities, construction and remodel job sites.
NOTICE! Many of these applications can present
significant health risks and require professional training.
Because federal, state/provincial, and local laws
and regulations have varying requirements for the
application, testing and general use of equipment on
asbestos abatement projects, Legend Brands cannot
warrant products for asbestos abatement. Contractors
performing abatement work should evaluate tools,
equipment and procedures in light of their local regulatory
requirements, and comply with those requirements.
WARRANTY REGISTRATION
Register at Warranty.LegendBrandsRestoration.com. If you
determine service is required, have your equipment model,
serial number and original proof of purchase available and call
your distributor to obtain a return material authorization (RMA)
or email service@legendbrandsrestoration.com.
SPECIAL FEATURES
Command Hub Technology
Integrated Command Hub technology with the free Command
Center mobile app enables firmware updates and 24/7
monitoring and control to ensure optimal air filtration. (App
available soon in Apple and Google Play stores.)
Ducting options
Inlet: 14 in. wire reinforced ducting (purchased separately).
Outlet: 14 in.(diameter) layflat or wire reinforced ducting
(purchased separately) using the provided duct attachment
ring. Take care not to bend or otherwise damage the
attachment ring when installing the ducting. Do not exceed a
maximum ducting length of 25 ft. / 7.6 m.
Negative Pressure Setup
The HEPA 700 can be set up for a negative pressure
containment area. Only professionals with the appropriate
training should set up negative pressure containment areas.
Stacking for Storage and Operation
Stack the HEPA 700 up to three high for storage or transport.
Secure the units when stacked for transport.
The unit can also be operated on its back, with the outlet
facing upward.
CONTROLS AND OPERATING
INSTRUCTIONS
Setup
1. Unwrap the cord completely.
2. Place the HEPA 700 with the handle up. Ensure that neither
the inlet nor the outlet are obstructed.
3. Plug in to a standard 115V GFCI-protected outlet.
124775B HEPA 700
Electrical Outlets
You can connect up to eight (8) HEPA 700s on a 15-amp
circuit on the lowest speed; four (4) on the highest speed.
Command Hub - Home
On/Off. Switches unit on or off.
Use + / - to adjust blower speed.
Menu. Select to view system info, service, error
messages, wireless setup, settings, and other information. Go
to HEPA700.legendbrandsrestoration.com for more info.
GFCI Outlet Reset and Test
MAINTENANCE
WARNING
ELECTRIC SHOCK HAZARD. Disconnect from
electrical supply prior to servicing or cleaning.
BREATHING HAZARD. Always wear an
appropriate NIOSH-approved respirator and
personal protective equipment when removing or
replacing filters, or when cleaning the HEPA 700.
About the filters
IMPORTANT: Use Legend Brands HEPA 700 filters only
(see Filter Options below). Use of other filters will
reduce filtration effectiveness.
Regularly check and replace the prefilter(s) and HEPA
primary filter as needed. The control panel will indicate
when the HEPA primary filter needs to be replaced.
Filters are not reusable. Do not attempt to clean and reuse.
NOTICE: When using the HEPA 700 on remediation
projects, change BOTH filters after every job. Dispose of
contaminated filters properly.
Replacing the Prefilter
The prefilter should be replaced more frequently to help
preserve the life of the HEPA filter.
1. Lay unit on its back and release the four (4) buckles. Lift off
the filter door.
2 Legend Brands, Inc.